UNIRAC EcoFoot2+ - System Components; EcoFoot2+ Core Components

INSTALLATION GUIDE
PAGE
7
10-DEGREE BALLASTED RACKING SYSTEM
SYSTEM COMPONENTS
EcoFoot2+ Core Components
EcoFoot2+ Base
Clevis Pin
Clamp-Lower
Deector
Clamp-Upper
Nut
A
D
B
E
C
F
C.NO. DESCRIPTION PART NUMBER
A EcoFoot2+ Base ES20207
B Universal Clamp Lower ES10459
C Universal Clamp Upper ES10458
D Clevis Pins ES10476-CP
E Deector ES20311
F Nut ES10277
G Mid-Support Upper ES11207
H Mid-Support Lower ES11208
C.NO. - Component Number
MFG APPROVAL DATE:
ENG APPROVAL DATE:
DESIGN DATE:
STATUS:
THIRD ANGLE
PROJECTION
PART MASS (lbs)
MATERIAL:
B
SHEET SIZE
FINISH:
Ecolibrium Solar,Inc.
244 West State St, Athens OH 45701
SCALE:
PART NAME:
DESIGNED BY:
ENGINEERING APPROVAL:
MANUFACTURING APPROVAL:
PART NUMBER:
TOLERANCES U.O.S DO NOT SCALE DRAWING
DIMENSIONS BASED ON ASME Y14.5-2009 STANDARD. SURFACE FINISH 125 √ ON
MACHINED SURFACES. ON PLATED PARTS DIMENSIONAL LIMITS APPLY AFTER PLATING.
DIMENSIONS OF MOLDED PARTS APPLY TO FINISHED PART; NO ALLOWANCE HAS BEEN
MADE FOR SHRINKAGE. USE STANDARD SAE GD&T FOR HARDWARE.
UNLESS OTHERWISE SPECIFIED:
.00 0.03"
.000 0.015"
ANGLES 2°
COLOR:
REVISION:
VIK GOPAL 12/17/19
JONAH COLES
PROTO/DEVEL/PROD
ELLIOT SMITH
B
* ALL DIMENSIONS IN INCHES
* BREAK ALL SHARP EDGES
* PARTS MUST HAVE NO
BURR OR FLARE ≥
SHEET 1 OF 1
ES11207
1:2
0.45
ASM
ASM
ASM
ECOFOOT 2+ MID SUPPORT UPPER
1
2
8.560
1.902
REVISIONS
REV. DESCRIPTION DATE DRAWN BY
A INITIAL RELEASE FOR PRODUCTION 12/17/2019 VG
B PART ES11204-CP REVISED 5/1/2020 VG
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 ES11204-CP ECOFOOT 2+ MID SUPPORT UPPER BRACKET 1
2
ES11206-CP ECOFOOT 2+ EPDM PAD 1
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
SOLIDWORKS Educational Product. For Instructional Use Only.
MFG APPROVAL DATE:
ENG APPROVAL DATE:
DESIGN DATE:
STATUS:
THIRD ANGLE
PROJECTION
PART MASS (lbs)
MATERIAL:
B
SHEET SIZE
FINISH:
Ecolibrium Solar,Inc.
244 West State St, Athens OH 45701
SCALE:
PART NAME:
DESIGNED BY:
ENGINEERING APPROVAL:
MANUFACTURING APPROVAL:
PART NUMBER:
TOLERANCES U.O.S DO NOT SCALE DRAWING
DIMENSIONS BASED ON ASME Y14.5-2009 STANDARD. SURFACE FINISH 125 √ ON
MACHINED SURFACES. ON PLATED PARTS DIMENSIONAL LIMITS APPLY AFTER PLATING.
DIMENSIONS OF MOLDED PARTS APPLY TO FINISHED PART; NO ALLOWANCE HAS BEEN
MADE FOR SHRINKAGE. USE STANDARD SAE GD&T FOR HARDWARE.
UNLESS OTHERWISE SPECIFIED:
.00 0.03"
.000 0.015"
ANGLES 2°
COLOR:
REVISION:
VIK GOPAL 12/17/19
JONAH COLES
PROTO/DEVEL/PROD
ELLIOT SMITH
B
* ALL DIMENSIONS IN INCHES
* BREAK ALL SHARP EDGES
* PARTS MUST HAVE NO
BURR OR FLARE ≥
SHEET 1 OF 1
ES11208
1:1
0.23
ASM
ASM
ASM
ECOFOOT 2+ MID SUPPORT LOWER
1
2
REVISIONS
REV. DESCRIPTION DATE DRAWN BY
A INITIAL RELEASE FOR PRODUCTION 12/17/2019 VG
B REVISED ES11205-CP 5/1/2020 VG
ITEM NO. PART NUMBER DESCRIPTION QTY.
1 ES11205-CP ECOFOOT 2+ MID SUPPORT LOWER BRACKET 1
2
ES11206-CP ECOFOOT 2+ EPDM PAD 1
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
SOLIDWORKS Educational Product. For Instructional Use Only.
Mid-Support Upper
Mid-Support Lower
G
H