Utilitech 148008 - User Manual

1
BOOSTER UTILITY PUMP
ITEM #0955585
MODEL #148008
Español p. 12
Serial Number
Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-866-994-4148, 7:30 a.m. - 5:00 p.m., EST, Monday - Friday.
ATTACH YOUR RECEIPT HERE
AB171106
SW1116 B
Validation #LBWU-002234874.

Utilitech 148008 Specifications

General

Model	148008
Category	Water Pump
Maximum pumping height	25 ft
Voltage	120V
Max Head	25 ft
Discharge pipe size	1-1/4 in
Outlet Size	1-1/4 in

Summary

Package Contents

Pump and Garden Hose Adapters

Lists the pump and garden hose adapters included in the package.

Safety Information

Electrical Shock Hazard

Keep motor dry, do not submerge, protect from wet weather, avoid cord in water.

Fire and Explosion Hazard

Pump only clear water, avoid flammable or explosive atmospheres.

Risk of Electric Shock (Pools;Handling)

Not for swimming pools; disconnect power before service, avoid wet hands.

Electrical Safety and Warnings

Grounding and Circuit Requirements

Ensure proper grounding, use GFCI, do not remove ground pin.

Handling and Environmental Risks

Avoid wet conditions, use in dry location, protect cord.

Operational and Injury Hazards

Disconnect power for service, mind thermal overload, pressure relief.

Product Operation Cautions

Voltage and Temperature Limits

Ensure 115V power source, observe liquid temperature limits.

Water Source and Protection

Keep water source clear of debris, protect from freezing.

Operational Hazards and Restrictions

Do not run dry, secure discharge, do not operate unattended.

Preparation and Tools

Pre-Installation Checks

Verify all parts are present before assembly.

Required Tools

Crescent wrench and pipe sealant/tape are needed.

General Pump Information

Pump Application

Designed for sprinkling lawns, gardens, emptying tanks, and boosting pressure.

Operational Limitations

Not designed for underwater use or flammable liquids.

Setup

Electrical Circuit Check

Have an electrician check the circuit for proper grounding before installation.

Power Source and Water Supply

Disconnect power before servicing; ensure water source is clear of debris.

Freezing and Dry Running Protection

Protect from freezing to avoid damage; do not run the pump dry.

Installation Instructions

Pumping from Lakes, Ponds, or Streams

Position pump close to water source, max 20 ft. vertical distance, on level support.

Inlet Connection

Connect with 1 in. NPT PVC or garden hose adapter; use reinforced hose from water sources.

Foot Valve and Strainer

Install a foot valve with strainer at the end of the inlet line to maintain prime.

Sealing Inlet Connections

Seal all inlet connections with sealant or tape to prevent air leaks.

Discharge and Boosting Pressure

Discharge Connection

Connect 1 in. NPT pipe or garden hose to the discharge port.

Boosting Water Pressure

Connect inlet to water supply, outlet to desired location; use reinforced hose.

Discharge Pressure vs. Gallons Per Hour

Table showing pump performance at different discharge pressures.

Technical Specifications

Details on power supply, temperature, circuit, connections, and depth rating.

Operating Instructions

Priming the Pump

Remove priming plug, fill pump with water, reinstall plug.

Connecting to Power

Turn pump off, connect cord to GFCI outlet; do not cut ground prong.

Starting the Pump

Turn pump on; if no water within 5 mins, turn off and check steps.

Troubleshooting Checks

Verify vertical distance, inlet line airtightness, and open valves.

Care and Maintenance

Motor Lubrication

Motor bearings are permanently lubricated; no additional lubrication needed.

Draining for Winter

Disconnect lines, remove drain plug, drain piping, and store pump indoors.

Troubleshooting

Motor Will Not Run

Check switch, fuse/breaker, starting switch, and wiring.

Motor Runs Hot;Overloads

Check wiring, voltage, pump enclosure venting, and inlet hose.

Motor Runs, No Water Delivered

Check priming, air leaks, water level, foot valve, frozen pipes, or impeller.

Warranty Information

Warranty Coverage and Duration

One year from purchase or two years from manufacture, covers defects in materials/workmanship.

Warranty Exclusions

Excludes damage from improper installation, abuse, accident, or lack of maintenance.

Liability Limitations

Manufacturer not liable for incidental, consequential, or special damages.

Replacement Parts List

Available Replacement Parts

Lists part numbers for Garden Hose Adapters, Drain Plug, and Impeller Kit.