Victron energy BlueSolar PWM-Pro SCC010020110 User Manual

63 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Manual

EN

Handleiding

NL

Manuel

FR

Anleitung

DE

Manual

ES

Manual

SE

BlueSolar PWM-Pro Charge Controller

12V | 24V - 5A SCC010005010

12V | 24V - 10A SCC010010010

12V | 24V - 20A SCC010020110

12V | 24V - 30A SCC010030010

IMPORTANT

• Always connect the battery first, in order to

allow the Controller to recognize system voltage

• Use a 12V (36 cells) solar array for a 12V system.

• Use a 24V (72 cells) solar array for a 24V system.

Questions and Answers:

S
Sandra HernandezAug 13, 2025
What to do if Victron energy BlueSolar PWM-Pro SCC010020110 Controller charging, load and battery indicator (red) flashing simultaneously?
- C
  Charles PerezAug 14, 2025
  If the charging, load, and battery indicators (red) are flashing simultaneously on your Victron energy Controller, it indicates a system voltage error. Verify that the battery voltage matches the controller's working voltage. You may need to change to a suitable battery or reset the working voltage. Press the load button to clear the malfunction.
J
jamesbarronAug 18, 2025
What to do if Victron energy BlueSolar PWM-Pro SCC010020110 Controller load status indicator red and fast flashing?
- J
  Jessica JohnsonAug 18, 2025
  If the load status indicator is red and fast flashing on your Victron energy Controller, it means there is a short circuit. Clear the short circuit and press the button; the controller will resume working after 3 seconds.
S
Shelley JamesAug 21, 2025
What to do if Victron energy BlueSolar PWM-Pro SCC010020110 Controller charging, load and battery indicator (orange) flashing simultaneously?
- W
  williamstimothyAug 21, 2025
  If the charging, load, and battery indicators (orange) are flashing simultaneously on your Victron energy Controller, it means the controller is experiencing over temperature. When the heat sink of the controller exceeds 85°C, the controller will automatically shut down. Once the temperature decreases to less than 75°C, the controller will restart.
K
Kelly BernardAug 25, 2025
How to fix the charging LED indicator off during daytime when sunshine falls on PV modules of Victron energy BlueSolar PWM-Pro SCC010020110?
- S
  Scott ElliottAug 26, 2025
  If the charging LED indicator is off during the daytime when sunshine falls on PV modules of your Victron energy Controller, the PV array might be disconnected. Check that PV and battery wire connections are correct and tight.
D
davislindseyAug 29, 2025
What to do if Victron energy BlueSolar PWM-Pro SCC010020110 Controller load status indicator red and slow flashing?
- J
  John GarciaAug 29, 2025
  If the load status indicator is red and slowly flashing on your Victron energy Controller, it indicates an overload. Remove or cut out the additional load and press the button. The controller will restart after 3 seconds.
G
gilbertshawnSep 1, 2025
Why is the green battery LED indicator fast flashing on my Victron energy Controller?
- A
  Alexis DelacruzSep 1, 2025
  The green battery LED indicator flashes rapidly on your Victron energy Controller because the battery voltage is higher than the over voltage disconnect voltage. Check the battery voltage. If it's too high, disconnect the solar module immediately and replace the controller.
T
Tina ThomasSep 5, 2025
What to do if Victron energy Controller Battery LED indicator RED and loads not working?
- D
  Dylan RosalesSep 5, 2025
  If the Battery LED indicator is RED and loads are not working on your Victron energy Controller, it means the battery is over discharged. The controller automatically cut off the output. The LED indicator will return to green when the battery is fully charged.
P
Paul PetersSep 9, 2025
Why is the Battery LED indicator orange on my Victron energy BlueSolar PWM-Pro SCC010020110 Controller?
- L
  Lauren HarrisSep 9, 2025
  The Battery LED indicator is orange on your Victron energy Controller because the battery is under voltage. The load output is normal. The Charging LED indicator will return to green automatically when fully charged.

Victron energy BlueSolar PWM-Pro SCC010020110 Specifications

General

Brand	Victron energy
Model	BlueSolar PWM-Pro SCC010020110
Category	Controller
Language	English

Summary

General Safety Information

Product Features Overview

Installation and Operation Guide

Initial System Voltage Setup

Always connect the battery first for system voltage recognition.

Indicator Status Descriptions

Controller Programming Options

Load Program Settings

Options for load control: manual, light ON/OFF, and timed modes.

Battery Type Configuration

Settings for Gel, Sealed AGM, and Flooded battery types.

Protection Mechanisms

Load Protection

Covers overload and short circuit protection for the load output.

Polarity and Sensor Protection

Protects against reverse polarity and sensor faults.

Thermal and Voltage Protection

Includes overheating protection and high voltage transient suppression.

Troubleshooting Guide

Technical Specifications

Battery Programming Details

Day/Night Timing Control

Company and Support Information

Related product manuals

BlueSolar PWM-Pro SCC010030010

Preview: BlueSolar PWM Series

BlueSolar PWM Series

Preview: Victron energy BlueSolar

Victron energy BlueSolar

Preview: BlueSolar MPPT 75/10

BlueSolar MPPT 75/10

Preview: BlueSolar MPPT 75/15

BlueSolar MPPT 75/15

Preview: BlueSolar MPPT 100/30

BlueSolar MPPT 100/30

Preview: BlueSolar MPPT 100/15

BlueSolar MPPT 100/15

Preview: BlueSolar MPPT 150/70

BlueSolar MPPT 150/70

Preview: BlueSolar MPPT 150/35

BlueSolar MPPT 150/35

Preview: Victron energy Lynx Smart BMS

Victron energy Lynx Smart BMS

Preview: SmartSolar MPPT 100/50

SmartSolar MPPT 100/50

Preview: SmartSolar MPPT 150/60-Tr

SmartSolar MPPT 150/60-Tr