Victron energy BlueSolar PWM-Pro SCC010010010 - User Manual

63 pages

To Next Page

To Next Page

Loading...

Manual

EN

Handleiding

NL

Manuel

FR

Anleitung

DE

Manual

ES

Manual

SE

BlueSolar PWM-Pro Charge Controller

12V | 24V - 5A SCC010005010

12V | 24V - 10A SCC010010010

12V | 24V - 20A SCC010020110

12V | 24V - 30A SCC010030010

IMPORTANT

• Always connect the battery first, in order to

allow the Controller to recognize system voltage

• Use a 12V (36 cells) solar array for a 12V system.

• Use a 24V (72 cells) solar array for a 24V system.

Questions and Answers

J
Jeffrey DonaldsonAug 12, 2025
What to do if Victron energy Controller charging, load and battery indicator (red) flashing simultaneously?
- C
  Chad CantrellAug 12, 2025
  If the charging, load, and battery indicators (red) are flashing simultaneously on your Victron energy Controller, it indicates a system voltage error. Verify that the battery voltage matches the controller's working voltage. You may need to change to a suitable battery or reset the working voltage. Press the load button to clear the malfunction.
D
dperryAug 16, 2025
What to do if Victron energy BlueSolar PWM-Pro SCC010010010 load status indicator red and fast flashing?
- E
  Elizabeth LewisAug 16, 2025
  If the load status indicator is red and fast flashing on your Victron energy Controller, it means there is a short circuit. Clear the short circuit and press the button; the controller will resume working after 3 seconds.
J
Jay JohnsonAug 19, 2025
What to do if Victron energy BlueSolar PWM-Pro SCC010010010 charging, load and battery indicator (orange) flashing simultaneously?
- T
  Travis HoAug 20, 2025
  If the charging, load, and battery indicators (orange) are flashing simultaneously on your Victron energy Controller, it means the controller is experiencing over temperature. When the heat sink of the controller exceeds 85°C, the controller will automatically shut down. Once the temperature decreases to less than 75°C, the controller will restart.
P
pamela28Aug 25, 2025
How to fix the charging LED indicator off during daytime when sunshine falls on PV modules of Victron energy Controller?
- M
  Mark EvansAug 25, 2025
  If the charging LED indicator is off during the daytime when sunshine falls on PV modules of your Victron energy Controller, the PV array might be disconnected. Check that PV and battery wire connections are correct and tight.
M
mccoymichaelAug 27, 2025
What to do if Victron energy BlueSolar PWM-Pro SCC010010010 Controller load status indicator red and slow flashing?
- S
  Stephen HarperAug 27, 2025
  If the load status indicator is red and slowly flashing on your Victron energy Controller, it indicates an overload. Remove or cut out the additional load and press the button. The controller will restart after 3 seconds.
M
maxwellantonioAug 31, 2025
Why is the green battery LED indicator fast flashing on my Victron energy BlueSolar PWM-Pro SCC010010010 Controller?
- M
  molinasandraAug 31, 2025
  The green battery LED indicator flashes rapidly on your Victron energy Controller because the battery voltage is higher than the over voltage disconnect voltage. Check the battery voltage. If it's too high, disconnect the solar module immediately and replace the controller.
R
Renee WatsonSep 3, 2025
What to do if Victron energy BlueSolar PWM-Pro SCC010010010 Controller Battery LED indicator RED and loads not working?
- J
  Jacqueline RobertsSep 3, 2025
  If the Battery LED indicator is RED and loads are not working on your Victron energy Controller, it means the battery is over discharged. The controller automatically cut off the output. The LED indicator will return to green when the battery is fully charged.
A
Ashley ThompsonSep 7, 2025
Why is the Battery LED indicator orange on my Victron energy Controller?
- A
  Angel RodriguezSep 8, 2025
  The Battery LED indicator is orange on your Victron energy Controller because the battery is under voltage. The load output is normal. The Charging LED indicator will return to green automatically when fully charged.

Victron energy BlueSolar PWM-Pro SCC010010010 Specifications

General

Model	BlueSolar PWM-Pro SCC010010010
Category	Controller
Type	PWM
Rated Charge Current	10A
Voltage	12/24V
Battery Voltage	12/24V
Maximum PV Open Circuit Voltage	50V
Humidity Range	95%, non-condensing
Protection	Over temperature
Temperature Compensation	-16mV/°C (12V), -32mV/°C (24V)

Summary

General Safety Information

Features

Installation and Operation

Programming the Controller

Protection

Troubleshooting

Technical Specifications

Battery Related Programming Options

Day;Night Timing Options

Related product manuals

BlueSolar PWM-Pro SCC010030010

BlueSolar PWM-Pro SCC010020110

Preview: BlueSolar PWM Series

BlueSolar PWM Series

Preview: BlueSolar PWM-Pro Series

BlueSolar PWM-Pro Series

Preview: Victron energy BlueSolar

Victron energy BlueSolar

Preview: BlueSolar MPPT 75/10

BlueSolar MPPT 75/10

Preview: BlueSolar MPPT 75/15

BlueSolar MPPT 75/15

Preview: BlueSolar MPPT 100/30

BlueSolar MPPT 100/30

Preview: BlueSolar MPPT 100/15

BlueSolar MPPT 100/15

Preview: BlueSolar MPPT 150/70

BlueSolar MPPT 150/70

Preview: BlueSolar MPPT 100/50

BlueSolar MPPT 100/50

Preview: BlueSolar MPPT 150/35

BlueSolar MPPT 150/35