Victron energy BlueSolar PWM-Pro Series

Questions and Answers

B
bartonmichaelAug 13, 2025
What to do if Victron energy BlueSolar PWM-Pro charging, load and battery indicator (red) flashing simultaneously?
- C
  Christopher LongAug 13, 2025
  If the charging, load, and battery indicators (red) are flashing simultaneously on your Victron energy Controller, it indicates a system voltage error. Verify that the battery voltage matches the controller's working voltage. You may need to change to a suitable battery or reset the working voltage. Press the load button to clear the malfunction.
E
Emily DanielAug 16, 2025
What to do if Victron energy BlueSolar PWM-Pro load status indicator red and fast flashing?
- K
  kristen62Aug 16, 2025
  If the load status indicator is red and fast flashing on your Victron energy Controller, it means there is a short circuit. Clear the short circuit and press the button; the controller will resume working after 3 seconds.
R
Rebecca DavisAug 20, 2025
What to do if Victron energy BlueSolar PWM-Pro charging, load and battery indicator (orange) flashing simultaneously?
- S
  Sara BeckerAug 20, 2025
  If the charging, load, and battery indicators (orange) are flashing simultaneously on your Victron energy Controller, it means the controller is experiencing over temperature. When the heat sink of the controller exceeds 85°C, the controller will automatically shut down. Once the temperature decreases to less than 75°C, the controller will restart.
M
Matthew FordAug 25, 2025
How to fix the charging LED indicator off during daytime when sunshine falls on PV modules of Victron energy BlueSolar PWM-Pro Controller?
- B
  Barbara TurnerAug 25, 2025
  If the charging LED indicator is off during the daytime when sunshine falls on PV modules of your Victron energy Controller, the PV array might be disconnected. Check that PV and battery wire connections are correct and tight.
J
Joshua LoweryAug 27, 2025
What to do if Victron energy BlueSolar PWM-Pro load status indicator red and slow flashing?
- E
  Eric BlackwellAug 27, 2025
  If the load status indicator is red and slowly flashing on your Victron energy Controller, it indicates an overload. Remove or cut out the additional load and press the button. The controller will restart after 3 seconds.
A
Angela MarquezAug 31, 2025
Why is the green battery LED indicator fast flashing on my Victron energy BlueSolar PWM-Pro?
- J
  Jonathan JohnsonAug 31, 2025
  The green battery LED indicator flashes rapidly on your Victron energy Controller because the battery voltage is higher than the over voltage disconnect voltage. Check the battery voltage. If it's too high, disconnect the solar module immediately and replace the controller.
C
Charles FordSep 4, 2025
What to do if Victron energy BlueSolar PWM-Pro Battery LED indicator RED and loads not working?
- D
  Dr. Tamara JonesSep 4, 2025
  If the Battery LED indicator is RED and loads are not working on your Victron energy Controller, it means the battery is over discharged. The controller automatically cut off the output. The LED indicator will return to green when the battery is fully charged.
W
william21Sep 7, 2025
Why is the Battery LED indicator orange on my Victron energy BlueSolar PWM-Pro Controller?
- D
  David MartinezSep 7, 2025
  The Battery LED indicator is orange on your Victron energy Controller because the battery is under voltage. The load output is normal. The Charging LED indicator will return to green automatically when fully charged.

Victron energy BlueSolar PWM-Pro Series Specifications

General

Type	PWM
Self Consumption	< 10mA
Nominal battery voltage	12 / 24V
Humidity	95%, non-condensing
Communication port	No
Voltage	12/24V
Battery Types	Gel, AGM, Flooded
Protection	Reverse polarity
Battery Voltage	12/24V