38
2. MULTI TAP CHORUS (MT CHORS)
.......................
Stereo In/Stereo Out 1
This model features independent chorus taps for
each of the left, center and right outputs, produc-
ing a feeling of depth and spaciousness.
[1] "SPEED"............................... 0.100...10.00 [Hz]
* Adjusts the modulation speed.
[2] "DEPTH".............................................0.0...10.0
* Adjusts the modulation depth.
[4] "TIME" ................................................0.0...10.0
Adjusts the delay time.
[6] "MIX"...................................................0.0...10.0
* Adjusts the mix amount of the effect.
3. CLASSIC FLANGER (CL FLANG)
................
Mono In/Mono Out 1
A model of a truly classic analogue flanger that
“unchained” a highly influential modern guitarist
who many hail as the “godfather of two handed
tapping.”
[1] "SPEED"............................... 0.100...10.00 [Hz]
* Adjusts the modulation speed.
[2] "DEPTH".............................................0.0...10.0
* Adjusts the modulation depth.
[3] "RESO"...............................................0.0...10.0
* Adjusts the amount of resonance.
[4] "MANUAL" ..........................................1.0...10.0
* Adjusts the center frequency of the sweep. If
DEPTH is set to 10, MANUAL will not function.
[5] "OFFSET"...........................................0.0...10.0
Adjusts the starting position of the LFO. If you
assign “FLN TRIG” to the control switch, the
LFO will be reset to the starting position speci-
fied by OFFSET whenever you operate the con-
trol switch. When you defeat BYPASS, the LFO
will start from the position you specify here.
(p.49 Control switch settings)
[6] "MIX"...................................................0.0...10.0
* Adjusts the mix amount of the effect sound.
CONTROL switch.................................... FLN TRIG
If you set the FLN TRIG: CONTROL switch set-
ting to “FLN TRIG,” the LFO will be reset to the
position specified by OFFSET whenever you
operate the switch. (p.49 Control switch settings)
4. BI CHORUS (BI CHORS)
.
......
Mono In/Mono Out
1 (Mode=S) Stereo In/Stereo Out 1 (Mode=P1, P2, P3)
This is a chorus model unique to VOX. It provides
two chorus units, CHORUS 1 and CHORUS 2, and
lets you connect the two units not only in series or in
parallel, but also to synchronize or de-synchronize
the two LFOs. It produces a variety of tones that
cover a range from wonderfully spacious sounds to
bizarre flanger-like sounds with complex modulation.
[1] "SPEED 1"............................ 0.100...10.00 [Hz]
* Adjusts the modulation speed of CHORUS 1.
[2] "DEPTH"...........................................0.0...10.00
* Adjusts the modulation depth of CHORUS 1/2.
[3] "RESO"...............................................0.0...10.0
* Adjusts the amount of resonance for CHO-
RUS 1/2.
[4] "SPEED 2" ............................0.100...10.00 [Hz]
* Adjusts the modulation speed of CHORUS 2.
NOTE: This will not function if MODE is set to P2 or
P3.
[5] "MODE"...........................................S/P1/P2/P3
Specifies the connection and LFO for CHORUS
1/2.
S: CHORUS 1/2 are connected in series.
P1: CHORUS 1/2 are connected in parallel.
P2: CHORUS 1/2 are connected in parallel,
and their LFOs are synchronized.
P3: CHORUS 1/2 are connected in parallel,
and their LFOs are synchronized in oppo-
site phase (Stereo mode).
NOTE: If P2 or P3 is selected, the speed is adjusted
by the SPEED 1 knob.
[6] "MIX".................................................. 0.0...10.0
* Adjusts the mix amount of the effect sound.
5. DUO PHASE (DUO PHAS).......
Mono In/Mono Out
2 (Mode=S1, S2) Stereo In/Stereo Out 2 (Mode=P1, P2, P3)
This is an amazing phaser that provides two six-
stage phasers; PHASER 1 and PHASER 2. They
can be connected in series (to make a pseudo-
twelve-stage phaser!) or in parallel, and you can
also synchronize or de-synchronize the two
LFOs.
[1] "SPEED 1" ............................0.100...10.00 [Hz]
* Adjusts the modulation speed of PHASER 1.
[2] "DEPTH" ............................................ 0.0...10.0
* Adjusts the modulation depth of PHASER 1/2.
[3] "RESO" .............................................. 0.0...10.0
* Adjusts the amount of resonance for PHASER
1/2.
[4] "SPEED 2" ............................0.100...10.00 [Hz]
* Adjusts the modulation speed of PHASER 2.
NOTE: This will not function if MODE is set to S2, P2,
or P3.
[5] "MODE"............................... S1, S2, P1, P2, P3
Specifies the connection and LFO for PHASER
1/2.
S1: PHASER 1/2 are connected in series.
S2: PHASER 1/2 are connected in series and
their LFOs are synchronized to create a
pseudo-twelve-stage phaser.
P1: PHASER 1/2 are connected in parallel.
P2: PHASER 1/2 are connected in parallel, and
their LFOs are synchronized (Stereo mode).
P3: PHASER 1/2 are connected in parallel,
and their LFOs are synchronized in oppo-
site phase (Stereo mode).
NOTE:
If S2, P2 or P3 is selected, the speed is
adjusted by the SPEED 1 knob.
To Next Page
Loading...
Need help?
General
