WAGNER Control Pro 150 - User Manual

28 pages

Save Page as PDF

To Next Page

0917 • Form No. 0580055D

CONTROL PRO

™

Owner‘s manual • GuIDe D‘uTIlIsaTIOn •

MANUAL DEL PROPIETARIO

READ THIS MANUAL FOR COMPLETE INSTRUCTIONS

FRANÇAIS  P. 24

ESPAÑOL  P. 48

wagner-group.com

Model 150

Model 170

Model 190

Other manuals for WAGNER Control Pro 150

Operating Instructions20 pages

Questions and Answers

D
Daniel SmithJul 25, 2025
What to do if my WAGNER Control Pro 150 stops spraying?
- K
  Kevin TaylorJul 25, 2025
  If the spray pattern becomes distorted or stops spraying completely while the gun is triggered, it could be due to a clogged spray tip or inlet filter. First, lock the spray gun and rotate the spray tip 180 degrees. If it's hard to rotate, relieve pressure by slowly turning the PRIME/SPRAY knob to PRIME, unlock the spray gun, and squeeze the trigger while pointing at scrap material. Release the trigger, lock the gun, and try rotating the tip again. Also, check the inlet filter; remove it from the suction tube and clean it with warm, soapy water for latex materials or mineral spirits for oil-based materials, then snap it back into place.
A
andersonjaneAug 10, 2025
How to fix a clogged spray tip on a WAGNER Paint Sprayer?
- J
  jessicagriffinAug 10, 2025
  If the spray pattern becomes distorted or stops spraying completely while the gun is triggered, the spray tip could be clogged. To fix this, lock the spray gun, then rotate the spray tip 180 degrees from its current position. If the spray tip is difficult to rotate, relieve pressure by slowly turning the PRIME/SPRAY knob to PRIME, unlock the spray gun, and squeeze the trigger while pointing it at scrap material. Release the trigger, lock the spray gun, and try rotating the spray tip again.

Summary

CONTROL PRO Owners Manual

Important Safety Information

General Safety Guidelines

Read manual, know controls, and proper usage.

Grounding Instructions

Electrical Grounding Requirements

Safety Hazards and Prevention

Explosion and Fire Hazards

Discusses flammable vapors, static electricity, and prevention measures.

Injection Injury Hazards

Warns about high-pressure streams and necessary precautions.

Additional Safety Precautions

Hazardous Vapors

Covers risks of inhaling fumes and protective measures.

General Handling and Environmental Safety

General Information and Specifications

Electrical Information and Specifications

Details electrical requirements, extension cords, and product specs.

Assembly Instructions

Attaching Main Components

Assembly Continuation

Connecting Spray Hose to Gun

Pre-Operation Procedures

Spray Gun Trigger Lock Operation

Pressure Relief Procedure

Outlines the critical steps to safely relieve pressure in the system.

Loading Spray Material

Materials and Preparation for Loading

System Priming Process

Step-by-step instructions for priming the sprayer with material.

Spraying Operation

Initial Spraying Setup

Covers initial pressure relief and setup before spraying.

Starting the Spraying Process

Guides on adjusting pressure, setting PRIME/SPRAY, and practicing.

Practice Spraying and Tip Selection

Control Pro Tip Selection Chart

Recommends spray tips based on coating type and pressure settings.

Understanding Spray Patterns

Spraying Techniques

Spray Gun Handling and Movement

Spray Distance and Surface Parallelism

Troubleshooting: Spray Tip Issues

Clearing a Clogged Spray Tip

Step-by-step guide to resolve a spray tip blockage.

Troubleshooting: Inlet Filter Issues

Cleaning the Inlet Filter

Instructions for removing and cleaning a clogged inlet filter.

Cleaning Procedures

Cleaning Notes and Supplies

Initial Disassembly and Soaking

Cleanup Continuation

Flushing and Rinsing the System

Details flushing the unit with cleaning solutions and water.

Final Reassembly and Purging

Long-Term Storage Preparation

Protecting Internal Components

Final Storage Steps and Handling

Inlet Valve Maintenance

Inlet Valve Cleaning and Inspection

Inlet Valve Reassembly and Lubrication

Outlet Valve Maintenance

Outlet Valve Cleaning and Inspection

Outlet Valve Reassembly and Grounding

Troubleshooting Common Issues

Power and Priming Problems

Addresses issues like the sprayer not turning on or drawing material.

Spray Pattern and Pressure Issues

Covers problems with spray pattern, pressure drops, and leaks.

Spray Gun and Tip Functionality

WAGNER Control Pro 150 Specifications

General

Type	Airless Paint Sprayer
Flow Rate	1.25 l/min
Hose Length	25 ft
Spray Tip Size	0.015 inch
Weight	19 lbs
Technology	Airless
Power Source	Electric
Nozzle Size	0.015 inch
Suitable For	Interior and Exterior Walls
Material Container Capacity	N/A (Direct Suction)