EasyManua.ls Logo

Water Ace R200A - User Manual

Water Ace R200A
24 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
R300A
R301A
R302A
R314A
R3065A
R3067A
R3183A
R3207A
R3254A
R30610A
R200A
R201A
R202A
R203A
R214A
CONSUMER HOT-LINE: 1-800-942-3343
Monday–Friday 7:30 AM to 5 PM CST
www.waterace.com
OWNER’S MANUAL Pgs. 2-8
4" SUBMERSIBLE PUMPS, TWO AND THREE WIRE,
1/2 THRU 1-1/2 HP 60 HZ
NOTICE D’UTILISATION Pgs. 9-15
POMPE SUBMERSIBLE DE 4 PO À DEUX ET
TROIS FILS, DE 1/2 À 1-1/2 CV 60 HZ
MANUAL DEL USUARIO Pgs. 16-22
BOMBA SUMERGIBLES DE 4" DE DOS Y
TRES ALAMBRES, DE 1/2 A 1-1/2 HP, 60 HZ
WATER ACE PUMP COMPANY | 293 WRIGHT ST. | DELAVAN, WI 53115
WA855 (11/5/08)

Table of Contents

Other manuals for Water Ace R200A

Preview: Installation Manual
Installation Manual36 pages

Questions and Answers

  • E
    Elizabeth SanchezAug 5, 2025
    What to do if my Water Ace R200A runs, but no water comes out?
    • K
      Kelsey BellAug 5, 2025
      If your Water Ace Water Pump is running but not delivering water, several issues could be the cause. It could be that the check valve is stuck—try shaking the pipe or raising and lowering the unit. If this doesn't work, remove the pump and clear any obstructions from the check valve. Other potential causes include a clogged intake (clean the screen or slots), worn impellers or diffuser (clean or replace them), a low well water level (lower the pump or install a low restrictor), or leaks (check all connections for airtightness). Also, low voltage to the pump can be a factor, so have the voltage checked by an electrician. The well might also be too deep for the pump.
  • J
    Jasmine HoustonAug 10, 2025
    Why won't my Water Ace R200A start?
    • M
      Michelle RobertsAug 10, 2025
      If your Water Ace Water Pump won't run, start by checking the fuse or circuit breaker. Also, inspect the piping for broken or open leads. If the fuse or breaker is fine, the pressure switch may be malfunctioning and need replacement. For 3-wire pumps, a control panel malfunction could also be the cause, so have an electrician check it.
  • M
    Michael HaynesAug 16, 2025
    How to fix a Water Ace R200A Water Pump that starts too often?
    • A
      Angela GallegosAug 16, 2025
      If your Water Ace Water Pump starts too frequently, here are some things to check: * The pressure switch might be out of adjustment; follow the instructions on the inside of the switch cover to adjust it. * The check valve could be stuck open or seated improperly; try cleaning or replacing it. * If you have a bladder tank, release air from the tank's air charge valve. If water bubbles or spits out, the bladder has a hole. For galvanized tanks, check for a defective air-volume control. * There may be a leak in the system.
  • C
    christina26Aug 23, 2025
    What to do if my Water Ace Water Pump won't shut off?
    • J
      jonathaningramAug 23, 2025
      If your Water Ace Water Pump does not shut off automatically, the pressure switch may be out of adjustment; follow the instructions on the inside of the switch cover. Alternatively, the pressure switch could be defective and need replacement. Other potential causes include a worn pump, a low well water level (lower the pump or install a flow restrictor). The well might also be too deep for the pump.
  • R
    Robin GonzalezAug 28, 2025
    Why does my Water Ace R200A Water Pump blow fuses or trip breakers?
    • T
      Tracey SteeleAug 28, 2025
      If your Water Ace Water Pump is blowing fuses, tripping breakers, or overloading, the fuses or breakers might be too small. Also, the wire size could be too small. A grounded motor or cable could also be the issue; have an electrician check it with an ohmmeter. Additionally, voltage that is too high or too low can cause these problems, so have it checked by an electrician. For 3-wire pumps, an incorrect control box could be the cause; compare the nameplate rating on the box to the pump HP.

Summary

Safety and Pre-Installation Guidance

General Safety Warnings

Explains safety alert symbols and hazard levels (Danger, Warning, Caution, Notice).

Specific Safety Instructions

Details on hazardous pressure, voltage, electrical shock, and installation practices.

Pre-Installation Requirements

Covers pump inspection, well development, and performance conditions.

Warranty Void Conditions

Lists specific situations that will void the product warranty.

Electrical Wiring and Grounding

Grounding and Wiring Standards

Requirements for permanent grounding, wire types, and electrical codes.

Wiring Connections Best Practices

Guidelines for connecting wires to avoid overheating and voltage drop.

Installation Wiring Instructions

Single Phase 3-Wire Setup

Specific instructions and warnings for 3-wire pump installations.

Single Phase 2-Wire Setup

Specific instructions and warnings for 2-wire pump installations.

Installation and Wire Splicing

Wire Splicing Techniques

Details on taped, heat shrink, and mechanical splice methods.

Power Supply Wire Installation

Procedures for securing power wires and proper grounding.

Pump Installation and Start-Up

Pump Installation Procedures

Guidelines for installing pump, pipe, and safety rope.

Initial Start-Up and Well Cleaning

Step-by-step process for starting a new well and clearing debris.

Tank and Water System Connection

Instructions for connecting pumps to tanks and installing relief valves.

Important Electrical Grounding

Critical information for safe electrical grounding of pump and motor.

Troubleshooting Common Problems

Motor Start Failures

Diagnosing and resolving issues when the motor won't start.

Fuse or Protector Trips

Troubleshooting blown fuses or tripped overload protectors.

Pump Cycling and Water Flow Issues

Addressing frequent pump starts and problems with water delivery.

Water Quality and Discharge Problems

Resolving issues like air or milky water discharge from faucets.

Limited Warranty Information

Warranty Terms and Conditions

Details on warranty coverage, eligibility, and claim procedures.

Warranty Exclusions and Limitations

Specifies conditions not covered and limitations of liability.

Special Product Warranty Notes

Notes for sewage pumps and exceptions to the standard warranty period.

Water Ace R200A Specifications

General IconGeneral
ModelR200A
CategoryWater Pump
Voltage115V
PhaseSingle
MaterialCast Iron
Horsepower0.5 HP
Inlet Size1.25 inches

Related product manuals