Water Right IMP-1044 User Manual (English)

Other manuals for Water Right IMP-1044

Installation Instructions And Owner's Manual32 pages

Questions and Answers:

J
John WilliamsSep 12, 2025
Why does Water Right Water Dispenser regenerate at the wrong time?
- A
  adam12Sep 12, 2025
  If your Water Right Water Dispenser control valve regenerates at the wrong time, consider the following: * **Power Outage:** Reset the time of day, especially after a power outage. If your PC board has battery backup, it may be depleted. Refer to the front cover and drive assembly drawing for instructions. * **Time of Day Setting:** Make sure the time of day is set correctly. * **Regeneration Time:** Verify the regeneration time is set correctly. * **Regeneration Setting:** Ensure the control valve isn't set to 'on 0' (immediate regeneration) or 'NORMAL + on 0' (delayed and/or immediate). Reset to NORMAL for a delayed regeneration time.
A
Amber JohnsonSep 12, 2025
Why does Water Right Water Dispenser use too much regenerant?
- J
  josephsandersSep 12, 2025
  If your Water Right Water Dispenser is using too much regenerant, consider these potential causes: * **Refill Setting:** Double-check the refill setting to ensure it's properly configured. * **Program Settings:** Review the program settings to make sure they are specific to your water quality and application needs. * **Frequent Regeneration:** Look for leaking fixtures that may be exhausting capacity, or the system may be undersized for your needs.
M
Megan AlvarezSep 12, 2025
What to do if Water Right IMP-1044 display doesn't show water flowing?
- D
  deanmitchellSep 13, 2025
  If the display on your Water Right Water Dispenser doesn't indicate water flow, check these items: * **Bypass Valve:** Ensure the bypass valve is not in the bypass position. Turn the bypass handles to place it in the service position. * **Meter Connection:** Verify the meter is connected to the meter connection on the PC board. * **Meter Turbine:** Remove the meter and check for rotation or any foreign material. * **Meter Wire:** Ensure the meter wire is securely installed into the three-pin connector labeled METER. * **Defective Meter:** Replace the meter if it is defective. * **Defective PC Board:** Replace the PC board if it is defective.
J
Jesse Brewer Jr.Sep 12, 2025
Why is water running to drain in Water Right IMP-1044 Water Dispenser?
- A
  Abigail SinghSep 12, 2025
  If water is constantly running to the drain in your Water Right Water Dispenser, here are some possible reasons: * **Power Outage:** A power outage during regeneration can cause this. Once power is restored, the control will finish the remaining regeneration time. Remember to reset the time of day. If the PC board has a battery backup, it may be depleted. Refer to the front cover and drive assembly drawing for instructions. * **Damaged Seal/Stack:** A damaged seal/stack assembly can lead to water running to the drain; consider replacing it. * **Piston Assembly Failure:** A failed piston assembly might be the culprit; replace the piston assembly. * **Loose Drive Cap:** Ensure the drive cap assembly is properly tightened.
M
michael82Sep 13, 2025
Why Water Right IMP-1044 control valve won't draw in regenerant?
- M
  michael02Sep 13, 2025
  If the control valve on your Water Right Water Dispenser isn't drawing in regenerant, here are some things to check: * **Injector:** The injector might be plugged. Remove it and clean or replace it. * **Regenerant Piston:** A faulty regenerant piston could be the problem. Replace it. * **Regenerant Line:** Inspect the regenerant line for any air leaks. * **Drain Line:** Check the drain line for restrictions or debris that could cause excess back pressure. Clean it to remove any obstructions. * **Drain Line Length/Height:** The drain line might be too long or too high. Shorten its length or height. * **Water Pressure:** Ensure the incoming water pressure is at least 25 psi.
U
uclaySep 13, 2025
Why does the time of day flash on my Water Right IMP-1044?
- M
  Michael MooreSep 13, 2025
  If the time of day display is flashing on and off on your Water Right Water Dispenser, here’s what to look into: * **Power Outage:** Reset the time of day, especially after a power outage. If your PC board has battery back up, it may be depleted. Refer to the front cover and drive assembly drawing for instructions. * **Drive Gear/Cap:** Check for a broken drive gear or drive cap assembly. Replace if necessary. * **Piston Rod:** A broken piston rod could be the cause. Replace it. * **PC Board:** The PC board might be defective.
S
Stephanie KimSep 14, 2025
What causes residual regenerant in Water Right IMP-1044 service water?
- J
  jacksonrobertSep 14, 2025
  If residual regenerant is being delivered to the service in your Water Right Water Dispenser, check the following: * **Water Pressure:** Ensure the incoming water pressure remains at a minimum of 25 psi. * **Injector:** The injector might be incorrect, damaged, or restricted. Replace it with the correct size for your application. * **Drain Line:** Inspect the drain line for any restrictions or debris and clean it.
A
Aaron GrayAug 29, 2025
Why is the time of day flashing on my Water Right Water Dispenser?
- B
  Brandon BakerAug 29, 2025
  If the time of day is flashing on and off on your Water Right Water Dispenser, it's likely due to a power outage. Reset the time of day. If the PC board has a battery backup, it may be depleted.
M
Michael LopezAug 25, 2025
What to do if Water Right IMP-1044 Water Dispenser control valve only regenerates when buttons are held?
- E
  Elizabeth PonceAug 26, 2025
  If your Water Right Water Dispenser's control valve doesn't regenerate automatically unless you press and hold the correct buttons, several factors could be responsible. First, check if the bypass valve is in the bypass position and turn the bypass handles to place it in the service position. Ensure the meter is correctly connected to the meter connection on the PC board. A restricted or stalled meter turbine can also cause this issue; remove the meter and check for rotation or foreign material. Incorrect programming could be the problem, so review the settings for errors. Also, verify that the meter wire is securely installed into the three-pin connector labeled METER. If these steps don't resolve the issue, the meter or the PC board might be defective and need replacement.
K
Katelyn HowardAug 26, 2025
Why does my Water Right IMP-1044 regenerate at the wrong time?
- R
  Robert KempAug 26, 2025
  If the control valve on your Water Right Water Dispenser regenerates at the wrong time of day, it could be due to several reasons. A power outage might have occurred; reset the time of day. If your PC board has a battery backup, it may be depleted. Also, the time of day might not be set correctly, so reset it to the correct time. The regeneration time itself might be set incorrectly, so reset that as well. Finally, the control valve might be set at immediate regeneration; check the programming and reset it to DELAYED for a delayed regeneration time.

Water Right IMP-1044 Specifications

General

Brand	Water Right
Model	IMP-1044
Category	Water Dispenser
Language	English

Summary

Pre-Installation Instructions for Dealers

Installer Settings and Procedures

Guidance for installers on programming, day override, and regeneration time settings.

Homeowner Guidance

Instructions for homeowners regarding bypass valve and operating displays.

Bypass Valve Operation

Normal Operation Position

Describes the bypass valve position for normal water flow through the softener.

Bypass Position

Details the bypass valve setting to isolate the softener from the plumbing system.

Diagnostic Position

Explains the diagnostic position for system testing without disrupting water supply.

Shut Off Position

Describes the shut off position to stop water flow to the building.

Installation

General Installation & Service Warnings

Key warnings and precautions for softener installation and service.

Site Requirements

Specifies site conditions and requirements for softener installation.

Grounding and Drain Line Installation

Instructions for electrical grounding and proper drain line setup.

Brine Tank and Overflow Connections

Details on connecting the brine tank and overflow lines.

Programming Procedures

Setting the Time of Day

Procedure for setting the current time on the control valve display.

Configuring Unit Settings

Steps to adjust water hardness, day override, and regeneration time.

Startup Instructions

Flushing the System

Steps to flush debris and air from the system after installation.

Startup Sequence Steps

Detailed procedure for initiating the system's first regeneration cycle.

Media Conditioning and Sanitization

Process for conditioning the softening media and sanitizing the unit.

Operating Displays and Maintenance

General Operation Displays

Overview of the different displays shown during normal system operation.

Regeneration Modes and Manual Control

Information on regeneration cycles and how to initiate manual regeneration.

Power Loss and Battery Replacement

Troubleshooting power outages and replacing the control valve battery.

Error Messages and Maintenance

Understanding error codes and performing routine brine tank maintenance.

Troubleshooting Guide

Display and Time of Day Errors

Resolving issues related to the control valve display and time settings.

Water Flow and Regeneration Issues

Diagnosing problems with water flow and automatic regeneration cycles.

Control Valve Motor and Movement Errors

Troubleshooting motor failures, incorrect movement, and stalled positions.

Specific Error Codes and Leak Detection

Addressing specific error codes and identifying potential leaks in the system.

Replacement Parts

Front Cover and Drive Assembly

Replacement parts for the control valve's front cover and drive mechanism.

Piston Assembly Parts

Catalog of replacement components for the piston assembly.

Bypass Valve and Related Components

Replacement parts for the bypass valve, brine elbow, and check valve.

Injector and Meter Components

Replacement parts for injector assemblies and the water meter.

Drain Line Assemblies

Parts list for 3/4" and 1" drain line assemblies.

Brine Tank and Safety Float Components

Replacement parts for the brine tank and safety float valve assembly.

Cabinet and Brine Well Components

Replacement parts for the unit's cabinet and brine well.

Installation Fitting Assemblies

1" PVC Male NPT & Solvent Elbow Fittings

Details on 1" PVC male NPT and solvent elbow fitting assemblies.

Brass Sweat Fittings

Replacement parts for brass sweat connection fittings.

Plastic Male NPT Fittings

Installation fittings for plastic male NPT connections.

Larger Size Brass and PVC Fittings

Parts for 1-1/4" & 1-1/2" brass sweat and PVC solvent fittings.

Shark Bite and John Guest Fittings

Replacement fittings for Shark Bite and John Guest connections.

Specifications

IM/IMC Model Specifications

Technical specifications for IM and IMC series water softeners.

IMRC Model Specifications

Technical specifications for IMRC series water softeners.

Cycle Times and Usage Data

Information on regeneration cycle times and water usage.

Water Softener Limited Warranty

Quick Reference Guide

General Operation Displays

Summary of system displays and how to navigate them.

Setting Time of Day and Bypass Operation

Quick steps for setting time and operating the bypass valve.

Programming and Manual Regeneration

Guides for initial programming and initiating manual regeneration.

Related product manuals

Water Right IMPC-1035

32 pages

Water Right Impression

16 pages

Water Right Impression RC Series

32 pages

Impression Plus Series

36 pages

Water Right IM-1044

32 pages

Water Right ISP1-1044

20 pages

Water Right ISP1-1054

20 pages

Water Right FFC-835-M

20 pages

Sanitizer Plus ASP1-1354

30 pages

Water Right IMP-1044 User Manual

Table of Contents

Other manuals for Water Right IMP-1044

Questions and Answers:

Water Right IMP-1044 Specifications

Summary

Pre-Installation Instructions for Dealers

Installer Settings and Procedures

Homeowner Guidance

Bypass Valve Operation

Normal Operation Position

Bypass Position

Diagnostic Position

Shut Off Position

Installation

General Installation & Service Warnings

Site Requirements

Grounding and Drain Line Installation

Brine Tank and Overflow Connections

Programming Procedures

Setting the Time of Day

Configuring Unit Settings

Startup Instructions

Flushing the System

Startup Sequence Steps

Media Conditioning and Sanitization

Operating Displays and Maintenance

General Operation Displays

Regeneration Modes and Manual Control

Power Loss and Battery Replacement

Error Messages and Maintenance

Troubleshooting Guide

Display and Time of Day Errors

Water Flow and Regeneration Issues

Control Valve Motor and Movement Errors

Specific Error Codes and Leak Detection

Replacement Parts

Front Cover and Drive Assembly

Piston Assembly Parts

Bypass Valve and Related Components

Injector and Meter Components

Drain Line Assemblies

Brine Tank and Safety Float Components

Cabinet and Brine Well Components

Installation Fitting Assemblies

1" PVC Male NPT & Solvent Elbow Fittings

Brass Sweat Fittings

Plastic Male NPT Fittings

Larger Size Brass and PVC Fittings

Shark Bite and John Guest Fittings

Specifications

IM/IMC Model Specifications

IMRC Model Specifications

Cycle Times and Usage Data

Water Softener Limited Warranty

Quick Reference Guide

General Operation Displays

Setting Time of Day and Bypass Operation

Programming and Manual Regeneration

Related product manuals