EasyManua.ls Logo

Water Right IMP-1054 - User Manual

Water Right IMP-1054
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Impression Series
®
Impression RC Series
Metered Water Softeners
For Models:
• IM-844 • IMP-844
• IM-948 • IMP-948
• IM-1044 • IMP-1044
• IM-1054 • IMP-1054
• IM-1248 • IMP-1248
• IM-1354 • IMP-1354
• IMC-835 • IMPC-835
• IMC-1035 • IMPC-1035
• IMRC-1054 • IMPRC-1054
• IMRC-1354 • IMPRC-1354

Table of Contents

Other manuals for Water Right IMP-1054

Preview: Installation Instructions And Owner's Manual
Installation Instructions And Owner's Manual32 pages

Questions and Answers

  • S
    Stephen WellsSep 9, 2025
    Why Water Right IMP-1054 Water Dispenser control valve doesn't regenerate automatically?
    • E
      Erika DelgadoSep 10, 2025
      If your Water Right Water Dispenser's control valve only regenerates when you press and hold the button, but not automatically, consider these possibilities: * **Bypass valve position:** Ensure the bypass handles are in the service position. * **Meter connection:** Check that the meter is properly connected to the meter connection on the PC board. * **Meter turbine:** Inspect the meter for any restrictions or debris. * **Programming:** Verify that the programming is correct. * **Meter wire security:** Ensure the meter cable wires are securely installed into the three-pin connector labeled METER. * **Meter condition:** Replace the meter if it's defective. * **PC board:** Replace the PC board if it's defective.
  • C
    Charles JordanAug 25, 2025
    What to do if Water Right IMP-1054 control valve only regenerates when buttons are held?
    • K
      Katherine LawsonAug 26, 2025
      If your Water Right Water Dispenser's control valve doesn't regenerate automatically unless you press and hold the correct buttons, several factors could be responsible. First, check if the bypass valve is in the bypass position and turn the bypass handles to place it in the service position. Ensure the meter is correctly connected to the meter connection on the PC board. A restricted or stalled meter turbine can also cause this issue; remove the meter and check for rotation or foreign material. Incorrect programming could be the problem, so review the settings for errors. Also, verify that the meter wire is securely installed into the three-pin connector labeled METER. If these steps don't resolve the issue, the meter or the PC board might be defective and need replacement.
  • B
    Brenda LeeAug 26, 2025
    Why does my Water Right IMP-1054 Water Dispenser regenerate at the wrong time?
    • T
      Tyler OlsonAug 26, 2025
      If the control valve on your Water Right Water Dispenser regenerates at the wrong time of day, it could be due to several reasons. A power outage might have occurred; reset the time of day. If your PC board has a battery backup, it may be depleted. Also, the time of day might not be set correctly, so reset it to the correct time. The regeneration time itself might be set incorrectly, so reset that as well. Finally, the control valve might be set at immediate regeneration; check the programming and reset it to DELAYED for a delayed regeneration time.
  • J
    Jared GriffinSep 23, 2025
    What to do if Water Right IMP-1054 control valve fails to draw in regenerant?
    • C
      christopher99Sep 23, 2025
      If the control valve on your Water Right Water Dispenser fails to draw in regenerant, consider these possible causes: * The injector may be plugged: Remove and replace the injector. * The regenerant piston may be faulty: Replace the regenerant piston. * There may be a leak in the regenerant line connection: Inspect the regenerant line for air leaks. * The drain line may have a restriction or debris causing excess back pressure: Inspect the drain line and remove any restrictions. * The drain line may be too long or too high: Shorten the length and/or height. * The water pressure may be low: Check the incoming water pressure, ensuring it remains at a minimum of 25 psi.
  • A
    Andrew SchultzSep 10, 2025
    Why Water Right IMP-1054 Water Dispenser PC board displays the wrong time?
    • A
      Antonio WolfeSep 10, 2025
      If the PC board on your Water Right Water Dispenser isn't showing the correct time, here are a few things to check: * **Outlet Usage:** Make sure the power adapter is plugged into an outlet that isn't controlled by a light switch. * **Breaker/GFI:** Check and reset the breaker switch or GFI switch if it has tripped. * **Power Outage:** Reset the time of day after a power outage. If your PC board has a battery backup, it might be depleted. See the front cover and drive assembly drawing for instructions. * **Defective PC Board:** If none of the above work, the PC board might be defective and need replacement.
  • S
    Stacey MooreSep 14, 2025
    What causes residual regenerant in Water Right Water Dispenser service water?
    • H
      hkingSep 14, 2025
      If residual regenerant is being delivered to the service in your Water Right Water Dispenser, check the following: * **Water Pressure:** Ensure the incoming water pressure remains at a minimum of 25 psi. * **Injector:** The injector might be incorrect, damaged, or restricted. Replace it with the correct size for your application. * **Drain Line:** Inspect the drain line for any restrictions or debris and clean it.
  • A
    Amanda LyonsSep 2, 2025
    How to troubleshoot no display on Water Right Water Filtration Systems?
    • A
      Amy FerrellSep 2, 2025
      If your Water Right Water Filtration System displays no image on the PC board, it could be due to several reasons: * There's no power at the electrical outlet. Solution: Repair the outlet or use a working one. * The control valve power adapter isn't plugged in. Solution: Plug the power adapter into the outlet, or connect the power cord to the PC board connection. * There's an improper power supply. Solution: Verify the correct voltage is being supplied to the PC board. * The power adapter is defective. Solution: Replace the power adapter. * The PC board itself is defective. Solution: Replace the PC board.
  • G
    Gina BrownSep 4, 2025
    Why Water Right Water Filtration Systems control valve fails to draw in regenerant?
    • R
      robin96Sep 5, 2025
      If your Water Right Water Filtration System's control valve fails to draw in regenerant, it could be due to: * A plugged injector. Solution: Remove the injector and clean or replace it. * A faulty regenerant piston. Solution: Replace the regenerant piston. * A regenerant line connection leak. Solution: Inspect the regenerant line for an air leak. * A drain line restriction or debris causing excess back pressure. Solution: Inspect the drain line and clean it to correct the restriction. * A drain line that's too long or too high. Solution: Shorten the length and/or height. * Low water pressure. Solution: Check the incoming water pressure – it must remain at a minimum of 25 psi.
  • L
    Linda CameronAug 29, 2025
    Why is the time of day flashing on my Water Right Water Dispenser?
    • J
      Justin MoranAug 29, 2025
      If the time of day is flashing on and off on your Water Right Water Dispenser, it's likely due to a power outage. Reset the time of day. If the PC board has a battery backup, it may be depleted.
  • K
    Kevin HullAug 29, 2025
    Why is my Water Right IMP-1054 delivering residual regenerant?
    • L
      Laura WilsonAug 29, 2025
      If residual regenerant is being delivered to the service in your Water Right Water Dispenser, it could be due to several reasons. Low water pressure might be the cause; check that the incoming water pressure remains at a minimum of 25 psi. The injector might be incorrect, damaged, or restricted; replace it with the correct size for your application. A restricted drain line could also be the issue; check for any obstructions and remove them.

Summary

Pre-Installation Instructions for Dealers

For the Installer

Essential tasks for installers before unit setup.

For the Homeowner

Sections homeowners should read before installation.

Bypass Valve

Normal Operation Position

Describes the normal water flow through the bypass valve.

Bypass Position

Details how to isolate the unit from water pressure.

Diagnostic Position

Explains the position for system testing and service.

Shut Off Position

How to completely shut off water to the building.

Installation

General Installation & Service Warnings

Important safety and installation precautions.

Site Requirements

Conditions and space needed for proper installation.

Well Water Installation

Specific installation guidance for well water systems.

Municipal Installation

Specific installation guidance for municipal water systems.

Installation (Continued)

Installing Ground

How to maintain electrical grounding during installation.

Drain Line

Proper installation and connection of the drain line.

Safety Brine Tank Connection

Connecting the brine tank safety float valve.

Overflow Line Connection

Installing the overflow line for safety.

Programming Procedures

Set Time of Day

Steps to set the current time on the control unit.

Unit Programming Steps

Detailed steps for programming unit settings like hardness.

Startup Instructions

Flushing of System

Procedures to flush debris and air after installation.

Cycle Descriptions

Names and descriptions of the softener's operational cycles.

Sanitizing the Unit

Steps to sanitize the softener after installation or service.

Operating Displays and Maintenance

General Operation Displays

Overview of system displays and information.

Regeneration Modes

Explains regeneration cycle and manual initiation.

Operating Displays and Maintenance (Continued)

Power Loss & Battery Replacement

Procedures for power outages and battery replacement.

Error Messages

How to interpret and respond to error codes.

Brine Tank Maintenance & Salt

Guidelines for maintaining the brine tank and salt levels.

RC Units (Resin Carbon)

Information on carbon units for water treatment.

Troubleshooting Guide

No Display on PC Board

Troubleshooting steps for a blank display screen.

Incorrect Time of Day Display

Diagnosing issues with the unit's time display.

No Water Flow Indication

Troubleshooting when the display doesn't show water flow.

Incorrect Regeneration Time

Resolving issues with regeneration occurring at the wrong time.

Troubleshooting Guide (Continued)

Automatic Regeneration Issues

Solving problems with automatic regeneration cycles.

Hard or Untreated Water Delivery

Diagnosing why the unit delivers hard or untreated water.

Excessive Regenerant Usage

Identifying causes of too much regenerant use.

Residual Regenerant Delivery

Troubleshooting residual regenerant in service water.

Troubleshooting Guide (Continued)

Regenerant Draw Failure

Steps for when the unit fails to draw regenerant.

Water Running to Drain

Diagnosing water continuously running to the drain.

Motor Movement Sensing Errors

Resolving errors related to motor movement sensing.

Motor Stalling Errors

Troubleshooting motor stalling during cycle positioning.

Troubleshooting Guide (Continued)

Motor Run Too Long Errors

Diagnosing errors where the motor runs excessively.

MAV;SEPS;NHBP Motor Issues

Troubleshooting motor issues for specific valve types.

Foreign Material in Valve

Clearing foreign material from valve assemblies.

Troubleshooting Guide (Continued)

Invalid Motor State;Cycle Errors

Resolving errors for invalid motor states or cycles.

Leak Detected Errors

Troubleshooting steps for detected leaks.

Memory Errors

Diagnosing and resolving memory-related error codes.

Replacement Parts

Front Cover and Drive Assembly

Parts for the control unit's front and drive mechanisms.

Piston Assembly Components

Replacement parts for the internal piston assembly.

Bypass Valve Components

Parts for the system's bypass valve assembly.

Injector Assemblies

Replacement injector parts for the softener.

Replacement Parts (Continued)

Drain Line Assemblies

Various drain line fittings and components.

Brine Tank Assembly Parts

Components for the brine tank and its safety valve.

Cabinet and Brine Tank Parts

Replacement parts for the unit's cabinet and brine tank.

Installation Fitting Assemblies

PVC and Solvent Elbow Fittings

Various PVC and solvent elbow connection fittings.

Brass Sweat Fittings

Installation fittings for brass sweat connections.

Plastic Male NPT Fittings

Male NPT fittings made of plastic.

Shark Bite and Guest Elbow Fittings

Shark Bite and John Guest elbow connection fittings.

Specifications

IM;IMC Series Specifications

Technical data for IM and IMC Impression series softeners.

IMRC Series Specifications

Technical data for IMRC Impression series softeners.

Cycle Times and Usage

Details on regeneration cycle durations and water usage.

Water Softener Limited Warranty

Ten Year Warranty Coverage

Warranty details for fiberglass mineral tanks (13" & smaller).

Five Year Warranty Coverage

Warranty details for control valves and larger tanks.

One Year Warranty Coverage

Warranty details for salt storage and other components.

Quick Reference Guide

General Operation Displays

Summary of system operating displays and navigation.

Error Code Reporting

How to report and interpret error codes.

Bypass Valve Operation

Quick guide to operating the bypass valve.

Setting Time of Day

Steps to reset the unit's time after power loss.

Adjusting Unit Settings

Quick guide to adjusting hardness and regeneration settings.

Manual Regeneration Guide

Instructions for initiating manual regeneration.

Water Right IMP-1054 Specifications

General IconGeneral
BrandWater Right
ModelIMP-1054
CategoryWater Dispenser
LanguageEnglish

Related product manuals