EasyManua.ls Logo

Water Right Impression RC Series - User Manual

Water Right Impression RC Series
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Impression Series
®
Impression RC Series
Metered Water Softeners
For Models:
• IM-844 • IMP-844
• IM-948 • IMP-948
• IM-1044 • IMP-1044
• IM-1054 • IMP-1054
• IM-1248 • IMP-1248
• IM-1354 • IMP-1354
• IMC-835 • IMPC-835
• IMC-1035 • IMPC-1035
• IMRC-1054 • IMPRC-1054
• IMRC-1354 • IMPRC-1354

Table of Contents

Questions and Answers

  • M
    matthew57Sep 15, 2025
    Why Water Right Water Dispenser control valve doesn't regenerate automatically?
    • L
      lauramedinaSep 15, 2025
      If your Water Right Water Dispenser's control valve only regenerates when you press and hold the button, but not automatically, consider these possibilities: * **Bypass valve position:** Ensure the bypass handles are in the service position. * **Meter connection:** Check that the meter is properly connected to the meter connection on the PC board. * **Meter turbine:** Inspect the meter for any restrictions or debris. * **Programming:** Verify that the programming is correct. * **Meter wire security:** Ensure the meter cable wires are securely installed into the three-pin connector labeled METER. * **Meter condition:** Replace the meter if it's defective. * **PC board:** Replace the PC board if it's defective.
  • P
    Patricia ChambersAug 25, 2025
    What to do if Water Right Water Dispenser control valve only regenerates when buttons are held?
    • T
      Traci SanchezAug 26, 2025
      If your Water Right Water Dispenser's control valve doesn't regenerate automatically unless you press and hold the correct buttons, several factors could be responsible. First, check if the bypass valve is in the bypass position and turn the bypass handles to place it in the service position. Ensure the meter is correctly connected to the meter connection on the PC board. A restricted or stalled meter turbine can also cause this issue; remove the meter and check for rotation or foreign material. Incorrect programming could be the problem, so review the settings for errors. Also, verify that the meter wire is securely installed into the three-pin connector labeled METER. If these steps don't resolve the issue, the meter or the PC board might be defective and need replacement.
  • M
    Mrs. Michelle ColemanAug 26, 2025
    Why does my Water Right Water Dispenser regenerate at the wrong time?
    • E
      Emily WillisAug 26, 2025
      If the control valve on your Water Right Water Dispenser regenerates at the wrong time of day, it could be due to several reasons. A power outage might have occurred; reset the time of day. If your PC board has a battery backup, it may be depleted. Also, the time of day might not be set correctly, so reset it to the correct time. The regeneration time itself might be set incorrectly, so reset that as well. Finally, the control valve might be set at immediate regeneration; check the programming and reset it to DELAYED for a delayed regeneration time.
  • J
    John HarrisSep 15, 2025
    Why Water Right Impression RC PC board displays the wrong time?
    • J
      Jeffery MurraySep 15, 2025
      If the PC board on your Water Right Water Dispenser isn't showing the correct time, here are a few things to check: * **Outlet Usage:** Make sure the power adapter is plugged into an outlet that isn't controlled by a light switch. * **Breaker/GFI:** Check and reset the breaker switch or GFI switch if it has tripped. * **Power Outage:** Reset the time of day after a power outage. If your PC board has a battery backup, it might be depleted. See the front cover and drive assembly drawing for instructions. * **Defective PC Board:** If none of the above work, the PC board might be defective and need replacement.
  • A
    Angela JonesSep 23, 2025
    What causes residual regenerant in Water Right Impression RC Water Dispenser service water?
    • J
      Julia HannaSep 23, 2025
      If residual regenerant is being delivered to the service in your Water Right Water Dispenser, check the following: * **Water Pressure:** Ensure the incoming water pressure remains at a minimum of 25 psi. * **Injector:** The injector might be incorrect, damaged, or restricted. Replace it with the correct size for your application. * **Drain Line:** Inspect the drain line for any restrictions or debris and clean it.
  • J
    Joseph YuSep 5, 2025
    How to troubleshoot no display on Water Right Water Filtration Systems?
    • S
      Stacey MendozaSep 5, 2025
      If your Water Right Water Filtration System displays no image on the PC board, it could be due to several reasons: * There's no power at the electrical outlet. Solution: Repair the outlet or use a working one. * The control valve power adapter isn't plugged in. Solution: Plug the power adapter into the outlet, or connect the power cord to the PC board connection. * There's an improper power supply. Solution: Verify the correct voltage is being supplied to the PC board. * The power adapter is defective. Solution: Replace the power adapter. * The PC board itself is defective. Solution: Replace the PC board.
  • D
    Danielle DavisSep 8, 2025
    Why Water Right Water Filtration Systems control valve fails to draw in regenerant?
    • H
      Heidi CooperSep 8, 2025
      If your Water Right Water Filtration System's control valve fails to draw in regenerant, it could be due to: * A plugged injector. Solution: Remove the injector and clean or replace it. * A faulty regenerant piston. Solution: Replace the regenerant piston. * A regenerant line connection leak. Solution: Inspect the regenerant line for an air leak. * A drain line restriction or debris causing excess back pressure. Solution: Inspect the drain line and clean it to correct the restriction. * A drain line that's too long or too high. Solution: Shorten the length and/or height. * Low water pressure. Solution: Check the incoming water pressure – it must remain at a minimum of 25 psi.
  • R
    Rebecca CummingsNov 23, 2025
    Why is my Water Right Impression RC delivering hard water?
    • M
      Martha SmithNov 23, 2025
      If your Water Right Water Dispenser is delivering hard or untreated water, consider the following potential causes. The bypass valve may be open or faulty; ensure it's fully closed or replace it. High water usage can exhaust the media; check program settings for abnormal usage. The meter might not be registering; remove it and check for rotation or obstructions. Water quality fluctuations may also be a factor; test the water and adjust program values. Additionally, check the regenerant tank for sufficient regenerant and add if necessary. If the control fails to draw in regenerant, refer to Troubleshooting Guide number 12. Also, ensure there's enough regenerant in the tank and check the refill flow control for any restrictions, replacing it if needed. Damaged seals, stack assembly, or pisto...
  • M
    Melissa GravesAug 30, 2025
    Why is the time of day flashing on my Water Right Water Dispenser?
    • A
      Amber HuntAug 30, 2025
      If the time of day is flashing on and off on your Water Right Water Dispenser, it's likely due to a power outage. Reset the time of day. If the PC board has a battery backup, it may be depleted.
  • Y
    yhortonAug 31, 2025
    Why is my Water Right Water Dispenser delivering residual regenerant?
    • C
      Christina WolfAug 31, 2025
      If residual regenerant is being delivered to the service in your Water Right Water Dispenser, it could be due to several reasons. Low water pressure might be the cause; check that the incoming water pressure remains at a minimum of 25 psi. The injector might be incorrect, damaged, or restricted; replace it with the correct size for your application. A restricted drain line could also be the issue; check for any obstructions and remove them.

Water Right Impression RC Series Specifications

General IconGeneral
BrandWater Right
ModelImpression RC Series
CategoryWater Dispenser
LanguageEnglish

Related product manuals