Water Right Impression RC Series - User Manual

Water Right Impression RC Series

32 pages

To Next Page

To Next Page

Loading...

Impression Series

®

Impression RC Series

Metered Water Softeners

For Models:

• IM-844 • IMP-844

• IM-948 • IMP-948

• IM-1044 • IMP-1044

• IM-1054 • IMP-1054

• IM-1248 • IMP-1248

• IM-1354 • IMP-1354

• IMC-835 • IMPC-835

• IMC-1035 • IMPC-1035

• IMRC-1054 • IMPRC-1054

• IMRC-1354 • IMPRC-1354

Table of Contents

Questions and Answers

M
Mrs. Michelle ColemanAug 26, 2025
Why does my Water Right Water Dispenser regenerate at the wrong time?
- E
  Emily WillisAug 26, 2025
  If the control valve on your Water Right Water Dispenser regenerates at the wrong time of day, it could be due to several reasons. A power outage might have occurred; reset the time of day. If your PC board has a battery backup, it may be depleted. Also, the time of day might not be set correctly, so reset it to the correct time. The regeneration time itself might be set incorrectly, so reset that as well. Finally, the control valve might be set at immediate regeneration; check the programming and reset it to DELAYED for a delayed regeneration time.
L
Lindsey RamirezAug 27, 2025
Why is my Water Right Impression RC Water Dispenser control valve not drawing in regenerant?
- C
  Christy BellAug 27, 2025
  If the control valve on your Water Right Water Dispenser is not drawing in regenerant, several issues could be the cause. The injector might be plugged; remove and replace it. A faulty regenerant piston could also be the problem, so replace it. Check the regenerant line for any air leaks. A restricted drain line could be causing excess back pressure; inspect and correct any restrictions. Ensure the drain line isn't too long or high; shorten it if necessary. Finally, low water pressure could be the issue; ensure it remains at a minimum of 25 psi.
O
obrienphilipAug 27, 2025
Why is there excessive water in my Water Right Impression RC regenerant tank?
- P
  Peter WoodAug 27, 2025
  If you notice excessive water in the regenerant tank of your Water Right Water Dispenser, several factors could be at play. Improper program settings could be the cause, so check the refill setting. The injector might be plugged; remove and replace it. Ensure the drive cap assembly is properly tightened. A damaged seal/stack assembly/piston could also lead to this issue, requiring replacement. Check the drain line for restrictions or kinks, and clear or unkink it. If the backwash flow controller is plugged, remove and replace it if necessary. Lastly, ensure the refill flow controller is installed.
K
kimlisaAug 27, 2025
Why does my Water Right Impression RC Water Dispenser use too much regenerant?
- C
  Casey JohnsonAug 28, 2025
  If your Water Right Water Dispenser's control valve is using too much regenerant, consider the following potential causes. The refill setting may be improper; check and adjust it. Incorrect program settings can also lead to excessive regenerant use, so ensure they are specific to your water quality and application needs. Additionally, frequent regeneration of the control valve could be the issue; check for leaking fixtures or if the system is undersized.
J
Jonathan BowenAug 28, 2025
Why does the Water Right Impression RC Water Dispenser PC board display the wrong time?
- A
  amanda55Aug 28, 2025
  If the PC board on your Water Right Water Dispenser isn't displaying the correct time of day, there might be a few reasons. The power adapter could be plugged into an electric outlet controlled by a light switch; use an uninterrupted outlet instead. A tripped breaker switch or GFI could also be the cause; reset them. A power outage might have occurred, so reset the time of day. If the PC board has a battery backup, the battery may be depleted. Lastly, the PC board itself could be defective, requiring replacement.
D
dawn95Aug 29, 2025
Why is water running to the drain in my Water Right Water Dispenser?
- S
  Savannah SalasAug 29, 2025
  If water is continuously running to the drain in your Water Right Water Dispenser, it could be due to a few reasons. A power outage during regeneration might have occurred; the control will finish the remaining regeneration time once power is restored. Reset the time of day. If the PC board has a battery backup, it may be depleted. A damaged seal/stack assembly or a piston assembly failure could also be the cause, requiring replacement. Lastly, ensure the drive cap assembly is properly tightened.
J
Jon DavidAug 29, 2025
Why does my Water Right Impression RC display not show water flowing?
- K
  Kristine AdamsAug 30, 2025
  If the display on your Water Right Water Dispenser doesn't indicate that water is flowing, several issues could be the cause. The bypass valve might be in the bypass position; turn the bypass handles to place it in the service position. Ensure the meter is connected to the meter connection on the PC board. A restricted or stalled meter turbine can also cause this issue; remove the meter and check for rotation or foreign material. Verify that the meter wire is securely installed into the three-pin connector labeled METER. If these steps don't resolve the issue, the meter or the PC board might be defective and need replacement.
M
Melissa GravesAug 30, 2025
Why is the time of day flashing on my Water Right Water Dispenser?
- A
  Amber HuntAug 30, 2025
  If the time of day is flashing on and off on your Water Right Water Dispenser, it's likely due to a power outage. Reset the time of day. If the PC board has a battery backup, it may be depleted.
Y
yhortonAug 31, 2025
Why is my Water Right Water Dispenser delivering residual regenerant?
- C
  Christina WolfAug 31, 2025
  If residual regenerant is being delivered to the service in your Water Right Water Dispenser, it could be due to several reasons. Low water pressure might be the cause; check that the incoming water pressure remains at a minimum of 25 psi. The injector might be incorrect, damaged, or restricted; replace it with the correct size for your application. A restricted drain line could also be the issue; check for any obstructions and remove them.
N
Nicholas FrancisAug 31, 2025
What to do if Water Right Impression RC Water Dispenser control valve won't regenerate even when holding buttons?
- S
  Scott OconnorSep 1, 2025
  If the control valve on your Water Right Water Dispenser does not regenerate automatically even when the correct buttons are pressed and held, several components could be faulty. A broken drive gear or drive cap assembly could be the problem, so replace them. The piston rod might be broken, requiring replacement. The PC board could be defective. Also, ensure the cover is installed correctly; reinstall it if necessary.

Water Right Impression RC Series Specifications

General

Brand	Water Right
Model	Impression RC Series
Category	Water Dispenser
Language	English

Related product manuals

Preview: Water Right Impression

Water Right Impression

Preview: Water Right Impression Series

Water Right Impression Series

Preview: Impression Plus Series

Impression Plus Series

Preview: Water Right IMP-844

Water Right IMP-844

Water Right IMP-948

Water Right IMP-1044

Water Right IMP-1054

Water Right IMP-1248

Water Right IMP-1354

Water Right IMP-1035

Water Right IMPC-1035

Water Right IM-1054