Why does time of day flashes on and off on Water Right Water Filtration Systems?
If the time of day flashes on and off on your Water Right Water Filtration System, it is due to: a power outage. Reset the time of day. If the PC board has battery back up present the battery may be depleted. See front cover and drive assembly drawing for instructions.
What to do if my Water Right Impression regenerates at the wrong time?
If your Water Right Water Dispenser's control valve regenerates at the wrong time of day, here are some things to check: * **Power Outage:** If there was a power outage, reset the time of day. If your PC board has a battery backup, the battery might be depleted. See the front cover and drive assembly drawing for instructions. * **Incorrect Time:** Make sure the time of day is set correctly. * **Regeneration Time:** Verify that the regeneration time is set correctly. * **Regeneration Setting:** Check that the control valve isn't set to “on 0” (immediate regeneration). Reset it to NORMAL for a delayed regeneration time. * **NORMAL + on 0 Setting:** Ensure the control valve isn't set to “NORMAL + on 0” (delayed and/or immediate). Reset it to NORMAL for a delayed regeneration time.
Why my Water Right Impression doesn't automatically regenerate?
If your Water Right Water Dispenser control valve doesn't regenerate automatically but does when you press and hold the correct buttons, consider these potential causes: * **Bypass Valve:** Ensure the bypass valve is in the service position. * **Meter Connection:** Check that the meter is connected to the meter connection on the PC board. * **Meter Turbine:** Inspect the meter turbine for any restrictions or stalls. Remove the meter to check for rotation or foreign material. * **Programming:** Verify that the programming is correct. * **Meter Wire:** Make sure the meter wire is securely installed into the three-pin connector labeled METER. * **Meter:** The meter might be defective and need replacement. * **PC Board:** The PC board could be defective and require replacement.
What to do if my Water Right Water Dispenser control valve does not regenerate automatically?
If your control valve isn't regenerating automatically, but does when you press and hold the correct buttons, consider these potential causes: * The bypass valve might be in the bypass position. * The meter might not be connected to the PC board. * The meter turbine could be restricted or stalled. * There might be incorrect programming. * The meter wire may not be securely installed. * The meter or PC board could be defective. Check the bypass valve position, meter connection, turbine, programming, and wiring. Replace any defective components as needed.
How to fix a Water Right Water Dispenser that does not regenerate automatically when button is pressed?
If the control valve doesn't regenerate automatically even when the correct buttons are pressed and held, it could be due to: * A broken drive gear or drive cap assembly. * A broken piston rod. * A defective PC board. * The cover being installed incorrectly. Replace the drive gear or drive cap assembly, replace the piston rod, or reinstall the cover correctly.
How to fix Water Right Impression when display does not indicate that water is flowing?
If the display on your Water Right Water Dispenser doesn't indicate water flow, check these potential issues: * Bypass valve position: Ensure the bypass handles are in the service position, not bypass. * Meter connection: Verify the meter is connected to the three-pin connection labeled METER on the PC board. * Meter turbine: Remove the meter and check for rotation or any foreign material that might be restricting it. * Meter wire installation: Make sure the meter cable wires are securely installed into the three-pin connector labeled METER. * Meter condition: The meter might be defective and need replacement. * PC board: The PC board might be defective and need replacement.
What to do if my Water Right Water Filtration System is running water to the drain?
Water running to the drain may be due to: * A power outage during regeneration: Upon power being restored, the control will finish the remaining regeneration time. Reset the time of day. If the PC board has battery backup, the battery may be depleted. See the front cover and drive assembly drawing for instructions. * A damaged seal/stack assembly: Replace the seal/stack assembly. * Piston assembly failure: Replace the piston assembly. * The drive cap assembly not being tightened properly: Retighten the drive cap assembly.
How to resolve 'E2, Err – 1002, Err – 102' error on Water Right Water Filtration Systems?
This error means the control valve motor ran too short and couldn't find the next cycle position. Try these steps: * Open the control valve and inspect the piston assembly and seal/stack assembly for foreign material. Press the NEXT and REGEN buttons for 3 seconds to resynchronize the software with the piston position, or disconnect the power supply from the PC board for 5 seconds and then reconnect. * Check the piston and seal/stack assembly, reduction gears, drive bracket, and main drive gear interface for mechanical binding. Press the NEXT and REGEN buttons for 3 seconds to resynchronize the software with the piston position, or disconnect the power supply from the PC board for 5 seconds and then reconnect. * Loosen the main drive gear. Press the NEXT and REGEN buttons for 3 seco...
Why Water Right Water Dispenser PC board does not display correct time?
If the PC board isn't displaying the correct time, it could be due to: * The power adapter being plugged into an outlet controlled by a light switch. * A tripped breaker switch and/or tripped GFI. * A power outage. * A defective PC board. Use an uninterrupted outlet, reset the breaker switch and/or GFI switch, and reset the time of day. If the PC board has a battery backup, the battery may be depleted.
Why does the time of day flash on my Water Right Impression?
If the time of day is flashing on and off on your Water Right Water Dispenser, it could be due to: * **Power Outage:** Reset the time of day. If the PC board has battery back up present the battery may be depleted. See the front cover and drive assembly drawing for instructions. * **Drive Gear/Cap:** A broken drive gear or drive cap assembly. Replace the drive gear or drive cap assembly. * **Piston Rod:** A broken piston rod. Replace the piston rod. * **PC Board:** A defective PC board.
Key steps for installers and homeowner reading requirements before operation.
Explanation of normal, bypass, diagnostic, and shut-off valve positions and their functions.
Safety warnings, plumbing material recommendations, and site requirement details.
Instructions for electrical grounding and proper drain line installation, including air gaps.
Details for connecting the brine tank safety float valve and overflow line to a drain.
Guide to setting the time of day, water hardness, day override, and regeneration time.
Procedures for flushing debris, conditioning media, and sanitizing the unit after installation.
Explains system displays, regeneration modes, and how to initiate manual regeneration.
Covers battery replacement, error messages, brine tank salt maintenance, and RC unit information.
Addresses common problems like no display, incorrect time, no water flow, and regeneration timing.
Solves issues related to hard water delivery and problems with drawing regenerant from the tank.
Details error codes related to motor movement, stalling, and drain line problems.
Addresses errors for motor timing, stalling, and incorrect valve configurations.
Covers errors for invalid motor states, leak detection, and memory-related issues.
Lists parts for the front cover, motor, PC board, and drive gears with part numbers.
Details parts for the piston assembly, O-rings, and control valve body with part numbers.
Lists components for the bypass valve, brine elbow, and check valve assemblies.
Details injector assemblies and water meter and meter plug components.
Lists parts for drain line assemblies, including DLFCs for 3/4" and 1" sizes.
Details brine tank parts, safety float assemblies, and brine well components.
Lists parts for the top and bottom cabinet assemblies and brine well.
Details various PVC and brass sweat fittings for installation, including NPT and sweat types.
Lists Shark Bite and John Guest elbow fitting assemblies for installation.
Provides detailed specifications for Impression/IMC models and cycle times for regeneration.
Outlines the warranty periods, exclusions, and claims process for the water softener.
Summarizes general operation, setting time, manual regeneration, and bypass valve procedures.
General| Brand | Water Right |
|---|---|
| Model | Impression Series |
| Category | Water Dispenser |
| Language | English |
To Next Page