EasyManua.ls Logo

Water Right IMP-844 - User Manual

Water Right IMP-844
32 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Impression Plus Series
®
Metered Water Softeners
For Models:
• IMP-844
• IMP-948
• IMP-1044
• IMP-1054
• IMP-1248
• IMP-1354
For Cabinet Models:
• IMPC-835
• IMPC-935
• IMPC-1035

Table of Contents

Other manuals for Water Right IMP-844

Preview: Installation Instructions & Owner's Manual
Installation Instructions & Owner's Manual32 pages

Questions and Answers

  • B
    Brittany HuntNov 26, 2025
    Why display doesn't indicate water is flowing in Water Right Water Filtration Systems?
    • W
      walterspamelaNov 26, 2025
      If your Water Right Water Filtration System's display doesn't show that water is flowing, here are some potential causes: * The bypass valve is in the bypass position. Solution: Turn the bypass handles to place the bypass in the service position. * The meter isn't connected to the meter connection on the PC board. Solution: Connect the meter to the three-pin connection labeled METER on the PC board. * The meter turbine is restricted or stalled. Solution: Remove the meter and check for rotation or foreign material. * The meter wire isn't securely installed into the three-pin connector. Solution: Verify that the meter cable wires are securely installed into the three-pin connector labeled METER. * The meter is defective. Solution: Replace the meter. * The PC board is defective. ...
  • D
    Dustin BirdAug 28, 2025
    Why Water Right Water Filtration Systems control valve fails to draw in regenerant?
    • E
      Elizabeth WilliamsAug 28, 2025
      If your Water Right Water Filtration System's control valve fails to draw in regenerant, it could be due to: * A plugged injector. Solution: Remove the injector and clean or replace it. * A faulty regenerant piston. Solution: Replace the regenerant piston. * A regenerant line connection leak. Solution: Inspect the regenerant line for an air leak. * A drain line restriction or debris causing excess back pressure. Solution: Inspect the drain line and clean it to correct the restriction. * A drain line that's too long or too high. Solution: Shorten the length and/or height. * Low water pressure. Solution: Check the incoming water pressure – it must remain at a minimum of 25 psi.
  • L
    lucasjacobAug 29, 2025
    Why does Water Right Water Filtration Systems control valve uses too much regenerant?
    • J
      Jennifer WoodsAug 29, 2025
      If your Water Right Water Filtration System's control valve uses too much regenerant, consider the following: * Improper refill setting. Solution: Check the refill setting. * Improper program settings. Solution: Check the program settings to ensure they are specific to the water quality and application needs. * The control valve regenerates frequently. Solution: Check for leaking fixtures that may be exhausting capacity, or the system may be undersized.
  • T
    Timothy MiddletonAug 30, 2025
    Why is there excessive water in the regenerant tank of my Water Right Water Filtration Systems?
    • M
      Mitchell SaundersAug 30, 2025
      If you observe excessive water in the regenerant tank of your Water Right Water Filtration System, it might be due to: * Improper program settings. Solution: Check the refill setting. * A plugged injector. Solution: Remove the injector and clean or replace it. * The drive cap assembly not being tightened properly. Solution: Retighten the drive cap assembly. * A damaged seal/stack assembly. Solution: Replace the seal/stack. * A restricted or kinked drain line. Solution: Check the drain line for restrictions or debris and/or unkink the drain line. * A plugged backwash flow controller. Solution: Remove the backwash flow controller and clean or replace it. * A missing refill flow controller. Solution: Replace the refill flow controller.
  • M
    Morgan GarciaAug 31, 2025
    Why does time of day flashes on and off on Water Right Water Filtration Systems?
    • C
      Christina SpenceSep 1, 2025
      If the time of day flashes on and off on your Water Right Water Filtration System, it is due to: a power outage. Reset the time of day. If the PC board has battery back up present the battery may be depleted. See front cover and drive assembly drawing for instructions.
  • K
    Kelly DixonNov 24, 2025
    What to do if Water Right Water Filtration Systems doesn't automatically regenerate?
    • R
      Rita ColemanNov 24, 2025
      If the control valve in your Water Right Water Filtration System doesn't regenerate automatically but does when you press and hold the correct buttons, consider these possibilities: * The bypass valve is in the bypass position. Solution: Turn the bypass handles to place the bypass in the service position. * The meter isn't connected to the meter connection on the PC board. Solution: Connect the meter to the three-pin connection labeled METER on the PC board. * The meter turbine is restricted or stalled. Solution: Remove the meter and check for rotation or foreign material. * There's incorrect programming. Solution: Check for programming errors. * The meter wire isn't installed securely into the three-pin connector. Solution: Verify that the meter cable wires are securely install...
  • M
    Monica GrantSep 18, 2025
    What causes residual regenerant in Water Right IMP-844 Water Dispenser service water?
    • J
      Jason SmithSep 22, 2025
      If residual regenerant is being delivered to the service in your Water Right Water Dispenser, check the following: * **Water Pressure:** Ensure the incoming water pressure remains at a minimum of 25 psi. * **Injector:** The injector might be incorrect, damaged, or restricted. Replace it with the correct size for your application. * **Drain Line:** Inspect the drain line for any restrictions or debris and clean it.
  • A
    Andre SmallNov 23, 2025
    Why is my Water Right Water Filtration System delivering hard water?
    • R
      richardnicoleNov 23, 2025
      If your Water Right Water Filtration System is delivering hard or untreated water, here's what might be happening: * The bypass valve is open or faulty. Solution: Fully close the bypass valve or replace it. * The media is exhausted due to high water usage. Solution: Check program settings or diagnostics for abnormal water usage. * The meter isn't registering. Solution: Remove the meter and check for rotation or foreign material. * There are water quality fluctuations. Solution: Test the water and adjust program values accordingly. * There's no regenerant or a low level of regenerant in the regenerant tank. Solution: Add the proper regenerant to the tank. * The control fails to draw in regenerant. Solution: Refer to Troubleshooting Guide number 12. * There's an insufficient r...
  • R
    Rachel WattsSep 12, 2025
    Why does Water Right IMP-844 regenerate at the wrong time?
    • J
      Joshua CunninghamSep 12, 2025
      If your Water Right Water Dispenser control valve regenerates at the wrong time, consider the following: * **Power Outage:** Reset the time of day, especially after a power outage. If your PC board has battery backup, it may be depleted. Refer to the front cover and drive assembly drawing for instructions. * **Time of Day Setting:** Make sure the time of day is set correctly. * **Regeneration Time:** Verify the regeneration time is set correctly. * **Regeneration Setting:** Ensure the control valve isn't set to 'on 0' (immediate regeneration) or 'NORMAL + on 0' (delayed and/or immediate). Reset to NORMAL for a delayed regeneration time.
  • M
    madison44Sep 9, 2025
    Why Water Right IMP-844 control valve doesn't regenerate automatically?
    • L
      Lisa WalkerSep 9, 2025
      If your Water Right Water Dispenser's control valve only regenerates when you press and hold the button, but not automatically, consider these possibilities: * **Bypass valve position:** Ensure the bypass handles are in the service position. * **Meter connection:** Check that the meter is properly connected to the meter connection on the PC board. * **Meter turbine:** Inspect the meter for any restrictions or debris. * **Programming:** Verify that the programming is correct. * **Meter wire security:** Ensure the meter cable wires are securely installed into the three-pin connector labeled METER. * **Meter condition:** Replace the meter if it's defective. * **PC board:** Replace the PC board if it's defective.

Summary

PREINSTALLATION AND BYPASS VALVE OPERATION

Dealer & Homeowner Instructions

Guidelines for installers and homeowners regarding pre-installation and operation.

Bypass Valve Positions

Detailed explanation of the four operational positions of the bypass valve.

INSTALLATION PROCEDURES

General Warnings, Site Requirements, and Plumbing

Installation warnings, site requirements, and initial plumbing considerations for setup.

Grounding, Drain Line, and Tank Connections

Instructions for electrical grounding, drain line, brine, and overflow line connections.

OPERATION, PROGRAMMING, AND START-UP

Programming Settings and Operation Displays

Steps for programming unit settings, understanding operation displays, and manual regeneration.

Start-Up Instructions and Sanitization

Procedures for flushing, initial regeneration, media conditioning, and unit sanitization.

TROUBLESHOOTING GUIDE

Display, Power, and Water Flow Issues

Solutions for problems related to the display, power supply, and water flow indication.

Regeneration, Water Quality, and Motor Issues

Fixing regeneration timing, water quality, motor control, and error code problems.

REPLACEMENT PARTS

Major Component Parts Lists

Replacement parts for drive assembly, piston, bypass valve, and injector components.

Tank, Drain, Meter, and Fitting Parts

Parts for drain lines, water meter, brine tanks, and installation fittings.

PERFORMANCE DATA AND WARRANTY

Performance Specifications

Detailed performance data and specifications for various water softener models.

Limited Warranty Information

Details on warranty periods, coverage, limitations, and claims process.

QUICK REFERENCE GUIDE

Operation, Settings, and Troubleshooting Summary

Quick guide to general operation, parameter settings, regeneration, error codes, and bypass valve.

Water Right IMP-844 Specifications

General IconGeneral
BrandWater Right
ModelIMP-844
CategoryWater Dispenser
LanguageEnglish

Related product manuals