Water Right IMP-844 - User Manual

Water Right IMP-844

32 pages

To Next Page

To Next Page

Loading...

Impression Plus Series

®

Metered Water Softeners

For Models:

• IMP-844

• IMP-948

• IMP-1044

• IMP-1054

• IMP-1248

• IMP-1354

For Cabinet Models:

• IMPC-835

• IMPC-935

• IMPC-1035

Table of Contents

Other manuals for Water Right IMP-844

Installation Instructions & Owner's Manual32 pages

Questions and Answers

G
garrett19Sep 13, 2025
Why does Water Right IMP-844 use too much regenerant?
- S
  swillisSep 13, 2025
  If your Water Right Water Dispenser is using too much regenerant, consider these potential causes: * **Refill Setting:** Double-check the refill setting to ensure it's properly configured. * **Program Settings:** Review the program settings to make sure they are specific to your water quality and application needs. * **Frequent Regeneration:** Look for leaking fixtures that may be exhausting capacity, or the system may be undersized for your needs.
A
ashleylyonsAug 23, 2025
How to troubleshoot no display on Water Right Water Filtration Systems?
- S
  Shane AllenAug 23, 2025
  If your Water Right Water Filtration System displays no image on the PC board, it could be due to several reasons: * There's no power at the electrical outlet. Solution: Repair the outlet or use a working one. * The control valve power adapter isn't plugged in. Solution: Plug the power adapter into the outlet, or connect the power cord to the PC board connection. * There's an improper power supply. Solution: Verify the correct voltage is being supplied to the PC board. * The power adapter is defective. Solution: Replace the power adapter. * The PC board itself is defective. Solution: Replace the PC board.
T
Tony BellSep 10, 2025
Why Water Right IMP-844 Water Dispenser PC board displays the wrong time?
- M
  margaretrothSep 10, 2025
  If the PC board on your Water Right Water Dispenser isn't showing the correct time, here are a few things to check: * **Outlet Usage:** Make sure the power adapter is plugged into an outlet that isn't controlled by a light switch. * **Breaker/GFI:** Check and reset the breaker switch or GFI switch if it has tripped. * **Power Outage:** Reset the time of day after a power outage. If your PC board has a battery backup, it might be depleted. See the front cover and drive assembly drawing for instructions. * **Defective PC Board:** If none of the above work, the PC board might be defective and need replacement.
M
madison44Sep 9, 2025
Why Water Right IMP-844 control valve doesn't regenerate automatically?
- L
  Lisa WalkerSep 9, 2025
  If your Water Right Water Dispenser's control valve only regenerates when you press and hold the button, but not automatically, consider these possibilities: * **Bypass valve position:** Ensure the bypass handles are in the service position. * **Meter connection:** Check that the meter is properly connected to the meter connection on the PC board. * **Meter turbine:** Inspect the meter for any restrictions or debris. * **Programming:** Verify that the programming is correct. * **Meter wire security:** Ensure the meter cable wires are securely installed into the three-pin connector labeled METER. * **Meter condition:** Replace the meter if it's defective. * **PC board:** Replace the PC board if it's defective.
A
Anna SmithSep 7, 2025
How to troubleshoot no display on Water Right IMP-844 PC board?
- J
  Jackson ThompsonSep 7, 2025
  If there is no display on the PC board of your Water Right Water Dispenser, here's what you can check: * **No power at the outlet:** Ensure the outlet is working. If not, repair it or use a different outlet. * **Power adapter issues:** Verify the control valve power adapter is properly plugged into the outlet and connected to the PC board. * **Power supply:** Confirm the correct voltage is being supplied to the PC board. * **Defective components:** Consider replacing the power adapter or the PC board if they are defective. * **Depleted battery:** Refer to the Operating Display and Maintenance section for instructions on battery replacement.
A
Alec BrandtSep 3, 2025
Why is Water Right Water Filtration Systems delivering residual regenerant?
- T
  Tyler TurnerSep 4, 2025
  If residual regenerant is being delivered to service in your Water Right Water Filtration System, it could be due to: * Low water pressure. Solution: Check the incoming water pressure – it must remain at a minimum of 25 psi. * Incorrect injector size. Solution: Replace the injector with the correct size for the application. * A restricted drain line. Solution: Check the drain line for restrictions or debris and clean it.
S
Steven HamptonSep 2, 2025
Why Water Right Water Filtration Systems P C board does not display correct time of day?
- E
  Erin FieldsSep 2, 2025
  If your Water Right Water Filtration System's PC board doesn't display the correct time of day, it could be due to: * The power adapter being plugged into an electric outlet controlled by a light switch. Solution: Use an uninterrupted outlet. * A tripped breaker switch and/or tripped GFI. Solution: Reset the breaker switch and/or GFI switch. * A power outage. Solution: Reset the time of day. If the PC board has battery back up present the battery may be depleted. See front cover and drive assembly drawing for instructions. * A defective PC board. Solution: Replace the PC board.
S
simmonssherrySep 1, 2025
Why is Water Right Water Filtration Systems running water to drain?
- C
  Chelsea MathisSep 2, 2025
  If your Water Right Water Filtration System is running water to the drain, it could be due to: * A power outage during regeneration. Solution: Upon power being restored, the control will finish the remaining regeneration time. Reset the time of day. If the PC board has a battery backup, the battery may be depleted. See the front cover and drive assembly drawing for instructions. * A damaged seal/stack assembly. Solution: Replace the seal/stack assembly. * Piston assembly failure. Solution: Replace the piston assembly. * The drive cap assembly not tightened properly. Solution: Retighten the drive cap assembly.
M
Morgan GarciaAug 31, 2025
Why does time of day flashes on and off on Water Right Water Filtration Systems?
- C
  Christina SpenceSep 1, 2025
  If the time of day flashes on and off on your Water Right Water Filtration System, it is due to: a power outage. Reset the time of day. If the PC board has battery back up present the battery may be depleted. See front cover and drive assembly drawing for instructions.
T
Timothy MiddletonAug 30, 2025
Why is there excessive water in the regenerant tank of my Water Right Water Filtration Systems?
- M
  Mitchell SaundersAug 30, 2025
  If you observe excessive water in the regenerant tank of your Water Right Water Filtration System, it might be due to: * Improper program settings. Solution: Check the refill setting. * A plugged injector. Solution: Remove the injector and clean or replace it. * The drive cap assembly not being tightened properly. Solution: Retighten the drive cap assembly. * A damaged seal/stack assembly. Solution: Replace the seal/stack. * A restricted or kinked drain line. Solution: Check the drain line for restrictions or debris and/or unkink the drain line. * A plugged backwash flow controller. Solution: Remove the backwash flow controller and clean or replace it. * A missing refill flow controller. Solution: Replace the refill flow controller.

Water Right IMP-844 Specifications

General

Brand	Water Right
Model	IMP-844
Category	Water Dispenser
Language	English

Summary

PREINSTALLATION AND BYPASS VALVE OPERATION

Dealer & Homeowner Instructions

Guidelines for installers and homeowners regarding pre-installation and operation.

Bypass Valve Positions

Detailed explanation of the four operational positions of the bypass valve.

INSTALLATION PROCEDURES

General Warnings, Site Requirements, and Plumbing

Installation warnings, site requirements, and initial plumbing considerations for setup.

Grounding, Drain Line, and Tank Connections

Instructions for electrical grounding, drain line, brine, and overflow line connections.

OPERATION, PROGRAMMING, AND START-UP

Programming Settings and Operation Displays

Steps for programming unit settings, understanding operation displays, and manual regeneration.

Start-Up Instructions and Sanitization

Procedures for flushing, initial regeneration, media conditioning, and unit sanitization.

TROUBLESHOOTING GUIDE

Display, Power, and Water Flow Issues

Solutions for problems related to the display, power supply, and water flow indication.

Regeneration, Water Quality, and Motor Issues

Fixing regeneration timing, water quality, motor control, and error code problems.

REPLACEMENT PARTS

Major Component Parts Lists

Replacement parts for drive assembly, piston, bypass valve, and injector components.

Tank, Drain, Meter, and Fitting Parts

Parts for drain lines, water meter, brine tanks, and installation fittings.

PERFORMANCE DATA AND WARRANTY

Performance Specifications

Detailed performance data and specifications for various water softener models.

Limited Warranty Information

Details on warranty periods, coverage, limitations, and claims process.

QUICK REFERENCE GUIDE

Operation, Settings, and Troubleshooting Summary

Quick guide to general operation, parameter settings, regeneration, error codes, and bypass valve.

Related product manuals

Water Right IMP-948

Water Right IMP-1044

Water Right IMP-1054

Water Right IMP-1248

Water Right IMP-1354

Water Right IMP-1035

Water Right IMPC-1035

Preview: Water Right Impression

Water Right Impression

Preview: Water Right Impression Series

Water Right Impression Series

Preview: Water Right Impression RC Series

Water Right Impression RC Series

Preview: Impression Plus Series

Impression Plus Series

Water Right IM-1044