To Next PageTo Next PageWhat does Err – 400 mean on my Water Right Water Dispenser?
If your Water Right Water Dispenser displays an Err – 400 error (viewable in the history screens), it indicates a memory-related issue. This could be due to a depleted battery (refer to the Operating Display and Maintenance section) or a defective PC board, which would need to be replaced.
What does Err – 202 mean on my Water Right Water Dispenser?
If you see Err – 202 on your Water Right Water Dispenser, viewable only in history screens, it could be due to a short power disruption. Check the transformer voltage and verify the power source. It might also be caused by dislodged foreign material; inspect the piston and stack for damage.
What does Err – 204 mean on my Water Right Impression RC Water Dispenser?
This error on your Water Right Water Dispenser occurs when the dP input is active for "ALARM" and the input is closed. The alarm buzzer will activate and the screen will display the error. Check for low flow leaks. Press NEXT and REGEN buttons for 3 seconds to resynchronize software with piston position or disconnect power supply from PC Board for 5 seconds and then reconnect to clear error.
How to troubleshoot no display on Water Right Impression RC PC board?
If there is no display on the PC board of your Water Right Water Dispenser, several issues could be the cause. First, the battery might be depleted (refer to the Operating Display and Maintenance section). Alternatively, the control valve power adapter may not be properly plugged into the outlet or connected to the PC board; ensure it is securely plugged in. It’s also possible the power supply is improper, so verify the correct voltage is reaching the PC board. If these steps don't resolve the issue, the power adapter or the PC board itself may be defective, requiring replacement. Finally, check that the electric outlet has power; repair the outlet or try a working one.
What does error code E3 mean on my Water Right Impression RC?
If your Water Right Water Dispenser displays error codes E3, Err – 1003, or Err – 103, it means the control valve motor ran too long and couldn't find the next cycle position. This could be because the drive bracket isn't snapped in properly, preventing the reduction gears and drive gear from interfacing correctly. Snap the drive bracket in properly, then press the NEXT and REGEN buttons for 3 seconds to resynchronize the software with the piston position, or disconnect the power supply from the PC board for 5 seconds and then reconnect it.
What to do if Water Right Impression RC Water Dispenser control valve won't regenerate even when holding buttons?
If the control valve on your Water Right Water Dispenser does not regenerate automatically even when the correct buttons are pressed and held, several components could be faulty. A broken drive gear or drive cap assembly could be the problem, so replace them. The piston rod might be broken, requiring replacement. The PC board could be defective. Also, ensure the cover is installed correctly; reinstall it if necessary.
Why is my Water Right Water Dispenser delivering residual regenerant?
If residual regenerant is being delivered to the service in your Water Right Water Dispenser, it could be due to several reasons. Low water pressure might be the cause; check that the incoming water pressure remains at a minimum of 25 psi. The injector might be incorrect, damaged, or restricted; replace it with the correct size for your application. A restricted drain line could also be the issue; check for any obstructions and remove them.
Why is the time of day flashing on my Water Right Water Dispenser?
If the time of day is flashing on and off on your Water Right Water Dispenser, it's likely due to a power outage. Reset the time of day. If the PC board has a battery backup, it may be depleted.
Why does my Water Right Impression RC display not show water flowing?
If the display on your Water Right Water Dispenser doesn't indicate that water is flowing, several issues could be the cause. The bypass valve might be in the bypass position; turn the bypass handles to place it in the service position. Ensure the meter is connected to the meter connection on the PC board. A restricted or stalled meter turbine can also cause this issue; remove the meter and check for rotation or foreign material. Verify that the meter wire is securely installed into the three-pin connector labeled METER. If these steps don't resolve the issue, the meter or the PC board might be defective and need replacement.
Why is water running to the drain in my Water Right Water Dispenser?
If water is continuously running to the drain in your Water Right Water Dispenser, it could be due to a few reasons. A power outage during regeneration might have occurred; the control will finish the remaining regeneration time once power is restored. Reset the time of day. If the PC board has a battery backup, it may be depleted. A damaged seal/stack assembly or a piston assembly failure could also be the cause, requiring replacement. Lastly, ensure the drive cap assembly is properly tightened.
General| Brand | Water Right |
|---|---|
| Model | Impression RC Series |
| Category | Water Dispenser |
| Language | English |
