Water Right IMP-1054 User Manual

Impression Series
®
Impression RC Series
Metered Water Softeners
For Models:
• IM-844 • IMP-844
• IM-948 • IMP-948
• IM-1044 • IMP-1044
• IM-1054 • IMP-1054
• IM-1248 • IMP-1248
• IM-1354 • IMP-1354
• IMC-835 • IMPC-835
• IMC-1035 • IMPC-1035
• IMRC-1054 • IMPRC-1054
• IMRC-1354 • IMPRC-1354

Water Right IMP-1054 Specifications

General

Brand	Water Right
Model	IMP-1054
Category	Water Dispenser
Language	English

Summary

Pre-Installation Instructions for Dealers

For the Installer

Essential tasks for installers before unit setup.

For the Homeowner

Sections homeowners should read before installation.

Bypass Valve

Normal Operation Position

Describes the normal water flow through the bypass valve.

Bypass Position

Details how to isolate the unit from water pressure.

Diagnostic Position

Explains the position for system testing and service.

Shut Off Position

How to completely shut off water to the building.

Installation

General Installation & Service Warnings

Important safety and installation precautions.

Site Requirements

Conditions and space needed for proper installation.

Well Water Installation

Specific installation guidance for well water systems.

Municipal Installation

Specific installation guidance for municipal water systems.

Installation (Continued)

Installing Ground

How to maintain electrical grounding during installation.

Drain Line

Proper installation and connection of the drain line.

Safety Brine Tank Connection

Connecting the brine tank safety float valve.

Overflow Line Connection

Installing the overflow line for safety.

Programming Procedures

Set Time of Day

Steps to set the current time on the control unit.

Unit Programming Steps

Detailed steps for programming unit settings like hardness.

Startup Instructions

Flushing of System

Procedures to flush debris and air after installation.

Cycle Descriptions

Names and descriptions of the softener's operational cycles.

Sanitizing the Unit

Steps to sanitize the softener after installation or service.

Operating Displays and Maintenance

General Operation Displays

Overview of system displays and information.

Regeneration Modes

Explains regeneration cycle and manual initiation.

Operating Displays and Maintenance (Continued)

Power Loss & Battery Replacement

Procedures for power outages and battery replacement.

Error Messages

How to interpret and respond to error codes.

Brine Tank Maintenance & Salt

Guidelines for maintaining the brine tank and salt levels.

RC Units (Resin Carbon)

Information on carbon units for water treatment.

Troubleshooting Guide

No Display on PC Board

Troubleshooting steps for a blank display screen.

Incorrect Time of Day Display

Diagnosing issues with the unit's time display.

No Water Flow Indication

Troubleshooting when the display doesn't show water flow.

Incorrect Regeneration Time

Resolving issues with regeneration occurring at the wrong time.

Troubleshooting Guide (Continued)

Automatic Regeneration Issues

Solving problems with automatic regeneration cycles.

Hard or Untreated Water Delivery

Diagnosing why the unit delivers hard or untreated water.

Excessive Regenerant Usage

Identifying causes of too much regenerant use.

Residual Regenerant Delivery

Troubleshooting residual regenerant in service water.

Troubleshooting Guide (Continued)

Regenerant Draw Failure

Steps for when the unit fails to draw regenerant.

Water Running to Drain

Diagnosing water continuously running to the drain.

Motor Movement Sensing Errors

Resolving errors related to motor movement sensing.

Motor Stalling Errors

Troubleshooting motor stalling during cycle positioning.

Troubleshooting Guide (Continued)

Motor Run Too Long Errors

Diagnosing errors where the motor runs excessively.

MAV/SEPS/NHBP Motor Issues

Troubleshooting motor issues for specific valve types.

Foreign Material in Valve

Clearing foreign material from valve assemblies.

Troubleshooting Guide (Continued)

Invalid Motor State/Cycle Errors

Resolving errors for invalid motor states or cycles.

Leak Detected Errors

Troubleshooting steps for detected leaks.

Memory Errors

Diagnosing and resolving memory-related error codes.

Replacement Parts

Front Cover and Drive Assembly

Parts for the control unit's front and drive mechanisms.

Piston Assembly Components

Replacement parts for the internal piston assembly.

Bypass Valve Components

Parts for the system's bypass valve assembly.

Injector Assemblies

Replacement injector parts for the softener.

Replacement Parts (Continued)

Drain Line Assemblies

Various drain line fittings and components.

Brine Tank Assembly Parts

Components for the brine tank and its safety valve.

Cabinet and Brine Tank Parts

Replacement parts for the unit's cabinet and brine tank.

Installation Fitting Assemblies

PVC and Solvent Elbow Fittings

Various PVC and solvent elbow connection fittings.

Brass Sweat Fittings

Installation fittings for brass sweat connections.

Plastic Male NPT Fittings

Male NPT fittings made of plastic.

Shark Bite and Guest Elbow Fittings

Shark Bite and John Guest elbow connection fittings.

Specifications

IM/IMC Series Specifications

Technical data for IM and IMC Impression series softeners.

IMRC Series Specifications

Technical data for IMRC Impression series softeners.

Cycle Times and Usage

Details on regeneration cycle durations and water usage.

Water Softener Limited Warranty

Ten Year Warranty Coverage

Warranty details for fiberglass mineral tanks (13" & smaller).

Five Year Warranty Coverage

Warranty details for control valves and larger tanks.

One Year Warranty Coverage

Warranty details for salt storage and other components.

Quick Reference Guide

General Operation Displays

Summary of system operating displays and navigation.

Error Code Reporting

How to report and interpret error codes.

Bypass Valve Operation

Quick guide to operating the bypass valve.

Setting Time of Day

Steps to reset the unit's time after power loss.

Adjusting Unit Settings

Quick guide to adjusting hardness and regeneration settings.

Manual Regeneration Guide

Instructions for initiating manual regeneration.