Water Right Sanitizer Plus ASP1-1354 User Manual

30 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Sanitizer Plus Series

®

Water Conditioners

Table of Contents

Questions and Answers:

H
holmesgregoryAug 17, 2025
What to do if display does not indicate that water is flowing in Water Right Water Dispenser?
- J
  James NunezAug 17, 2025
  If the display on your Water Right Water Dispenser doesn't indicate water flow, first ensure the bypass handles are correctly positioned for service. Then, check if the meter is properly connected to the PC board's meter connection. Also, verify that the meter cable wires are securely installed into the three-pin connector labeled 'METER'. Finally, examine the meter for any obstructions or rotation issues. If these steps don't resolve the issue, the meter or PC board might be defective and require replacement.
C
Christine LopezAug 19, 2025
Why does Water Right Sanitizer Plus ASP1-1354 control valve regenerates at wrong time of day?
- Y
  youngjessicaAug 19, 2025
  If your Water Right Water Dispenser control valve regenerates at the wrong time, it might be due to a power outage, which requires resetting the time of day. Also, verify that the time of day and regeneration time are set correctly. Ensure the control valve is not set to 'on 0' or 'NORMAL + on 0'; it should be set to 'NORMAL' for delayed regeneration.
S
scott63Aug 22, 2025
What to do if Water Right Sanitizer Plus ASP1-1354 Water Dispenser delivers hard or untreated water?
- R
  rfoxAug 22, 2025
  If you have hard or untreated water being delivered by your Water Right Water Dispenser, the bypass valve may be open or faulty, requiring you to fully close or replace it. High water usage can exhaust the media, so check program settings or diagnostics for abnormal usage. Also, inspect the meter for proper registration and any obstructions. Ensure there's an adequate level of regenerant in the tank and that the control is drawing it in correctly. Check the refill setting and flow control for any issues. If problems persist, the seal/stack assembly may be damaged, the media bed fouled, or the control valve and piston types mismatched, all of which would require replacement.
M
Mr. James GomezAug 25, 2025
Why Water Right Sanitizer Plus ASP1-1354 Water Dispenser doesn't regenerate automatically unless the buttons are pressed?
- J
  Jonathan Mckinney Jr.Aug 26, 2025
  If your Water Right Water Dispenser control valve does not regenerate automatically but does when you depress and hold the correct buttons, ensure the bypass valve is not in the bypass position by turning the bypass handles to the service position. Check that the meter is connected to the meter connection on the PC board and that the meter cable wires are securely installed into the three pin connector labeled METER. Remove the meter to check for rotation or foreign material that may be causing a restricted or stalled meter turbine. Verify the programming is correct. If these steps do not solve the problem, the meter or PC board may be defective and require replacement.
M
Matthew MartinAug 28, 2025
How to fix no display on Water Right Sanitizer Plus ASP1-1354 Water Dispenser PC board?
- C
  Christine JonesAug 28, 2025
  If the display on the PC board of your Water Right Water Dispenser is blank, verify that the electric outlet has power and use a working outlet if necessary. Ensure the control valve power adapter is plugged into the outlet and connected to the PC board. Confirm the power supply is delivering the correct voltage to the PC board. If these steps don't resolve the issue, the power adapter or PC board may be defective and require replacement.
M
Melanie AlvarezAug 30, 2025
Why time of day flashes on and off on Water Right Water Dispenser?
- D
  Dalton GoodmanAug 30, 2025
  If the time of day flashes on and off on your Water Right Water Dispenser, it is likely due to a power outage. Reset the time of day. If your PC board has a battery backup, the battery may be depleted.
K
Katie HernandezSep 2, 2025
Why Water Right Water Dispenser control valve uses too much regenerant?
- K
  Kara Hines MDSep 2, 2025
  If your Water Right Water Dispenser control valve uses too much regenerant, examine the refill setting and program settings to ensure they are specific to your water quality and application needs. Also, check for leaking fixtures or an undersized system that may be causing frequent regenerations.
N
Nathaniel VargasSep 5, 2025
How to fix PC board does not display correct time of day on Water Right Sanitizer Plus ASP1-1354?
- S
  Sean KingSep 5, 2025
  If the PC board on your Water Right Water Dispenser does not display the correct time of day, ensure the power adapter is plugged into an uninterrupted outlet, not one controlled by a light switch. Reset any tripped breaker switches or GFI switches. After a power outage, reset the time of day; if the PC board has a battery backup, the battery may be depleted. If the problem persists, the PC board may be defective and require replacement.
S
Sarah HallSep 7, 2025
What causes excessive water in regenerant tank of Water Right Water Dispenser?
- D
  Donald StevensonSep 7, 2025
  If there's excessive water in the regenerant tank of your Water Right Water Dispenser, start by checking the refill setting in the program. Then, inspect the injector for clogs and clean or replace it. Ensure the drive cap assembly is properly tightened. Also, check the drain line for restrictions or kinks and clear them. Finally, inspect the backwash flow controller for clogs and replace the refill flow controller if it's missing. If these steps don't resolve the issue, the seal/stack assembly may be damaged and require replacement.
S
Steven CarpenterSep 12, 2025
What to do if Water Right Water Dispenser control valve does not regenerate automatically when buttons are depressed?
- A
  apearsonSep 12, 2025
  If your Water Right Water Dispenser control valve does not regenerate automatically when the correct buttons are depressed and held, the drive gear or drive cap assembly could be broken, requiring replacement. Alternatively, the piston rod may be broken and also require replacement. A defective PC board could also be the cause.

Water Right Sanitizer Plus ASP1-1354 Specifications

General

Brand	Water Right
Model	Sanitizer Plus ASP1-1354
Category	Water Dispenser
Language	English

Summary

Installation and Setup Guide

Pre-Installation Instructions for Dealers

Instructions for dealers before installation, covering initial settings and checks.

Bypass Valve Operation

Explains the four positions and operation of the bypass valve.

General Installation Warnings

Critical safety and installation guidelines to follow during setup.

Site Requirements

Drain Line Installation

Start-Up and Programming Procedures

Start-Up Instructions

Guides the user through the initial start-up process and regeneration sequence.

Programming Procedures

Details how to set time, hardness, and regeneration schedules.

Setting Regeneration Time and Alarms

Operating Displays and Controls

General Operation Displays

Regeneration Modes and Manual Control

Error Messages and Maintenance

Guides on interpreting errors and brine tank maintenance.

Troubleshooting Common Issues

Display and Power Issues

Addresses problems with no display or incorrect time.

Regeneration and Water Quality Problems

Troubleshoots regeneration timing and water quality issues.

Error Code Diagnosis

Provides solutions for various error codes and motor issues.

Replacement Parts

Front Cover and Drive Assembly Parts

Piston Assembly Parts

Bypass Valve Parts

Injector Assemblies and Chlorine Generator

Brine Tank Assembly Parts

Specifications

Model Specifications

Cycle Times and Usage

Related product manuals

Sanitizer Plus ASP1-1054

Sanitizer Plus ASP2-1054

Water Right IM-1044

Water Right FF-948-M

Water Right IMP-1354

Water Right IMP-1054

Preview: Water Right ISP1-1044

Water Right ISP1-1044

Water Right IMPC-1035

Water Right ISP1-1054

Preview: Water Right Impression

Water Right Impression

Preview: Water Right Impression RC Series

Water Right Impression RC Series

Preview: Impression Plus Series

Impression Plus Series