Home
Yaesu
Repeater
WIRES-X FT3D
Yaesu WIRES-X FT3D User Manual
5
of 1
of 1 rating
62 pages
Give review
Manual
Specs
To Next Page
To Next Page
Loading...
Wide-Coverage Internet Repeater Enhancement System
WIRES-X Portable Digital Node Function
Instruction Manual
The C4FM digital transceivers that support the Portable Digital Node Function are
FT3D, FT2D, FTM-400XD/D, FTM-100D and FTM-300D. (As of May 2020)
Other C4FM digital transceivers do not require WIRES-X user registration and may
immediately enjoy Internet communications by connecting to a WIRES-X local node
that is within radio range.
2
Table of Contents
Preparation Procedure
2
Table of Contents
3
Introduction
4
What Is WIRES-X
4
What Is WIRES-X Portable Digital Node Function
4
System Requirements (Operating Environment)
7
Preparation
8
User Registration (Acquire an ID Number)
8
Install Latest WIRES-X Software to the PC
9
Install the USB Driver for the PC Connection Cable
12
Update the Firmware of the Transceiver
12
Connect the Transceiver and the PC
14
Communicating Only with C4FM Digital Mode (Portable Digital Node Mode)
14
Communicating with Digital or Analog FM Mode (Portable HRI Mode)
15
Initial Setting (Setting Is Required Only Once at the Beginning)
17
Start the Transceiver
17
Starting the WIRES-X Software
18
Communication Port Setting
18
Authenticate (Activate) the WIRES-X Server
19
Transceiver Settings (Access Point Only)
20
Basic Operation
22
Using the Portable Digital Node Mode
22
Connecting the Transceiver and the PC
22
Starting the WIRES-X Software
22
Starting the Transceiver in Special Mode
22
Setting the Transceiver (Access Point Only)
23
Start Operation of Portable Node
28
Connecting to a Node or a Room on the Internet
35
Communicating with Other Station
45
Disconnecting from the Node or Room
45
Closing the WIRES-X Software
45
Using the Portable HRI Mode
48
Connecting the Transceiver and the PC
48
Starting the WIRES-X Software
48
Starting the Transceiver in Special Mode
48
Connecting a Node or a Room by Operating the WIRES-X Software on the PC
49
Communicating with Other Station
49
Disconnecting from the Node or Room
50
Closing the WIRES-X Software
50
Operating the Transceiver in Portable HRI Mode
50
Ft3D/Ft2D
50
Ftm-400Xd/D
51
Ftm-300D
51
Ftm-100D
51
WIRES-X Software Main Screen
52
Functions to Use as Necessary
55
Audio Volume Adjustment of PC (Portable HRI Mode Only)
55
Adjusting Audio Level in the Access Point (Portable HRI Mode)
55
Adjusting Audio Level in the Direct Operation (Portable HRI Mode)
57
FT3D/FT2D Direct Operation Dedicated Function
60
Bookmarking Frequently Connected Nodes or Rooms
61
Bookmarking Nodes or Rooms
61
5
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Yaesu WIRES-X FT3D and is the answer not in the manual?
Ask a question
Yaesu WIRES-X FT3D Specifications
General
Frequency Range
144-148 MHz, 430-450 MHz
GPS
Yes
Bluetooth
Yes
WIRES-X
Yes
APRS
Yes
Operating Modes
FM, C4FM
Dimensions
62 x 100 x 32.5 mm
Related product manuals
Yaesu WIRES-X FTM-300D
62 pages
Yaesu Wires-X
39 pages
Yaesu WIRES-X HRI-200
107 pages
Yaesu WIRES-X TM-400FT5D
62 pages
Yaesu C4FM
10 pages
Yaesu DR-1
39 pages
Yaesu FTR-710A
154 pages
Yaesu DR-2X
56 pages
Yaesu DR-1X
48 pages
Yaesu FTR-2410A
154 pages
Yaesu FTR-5410
154 pages
Yaesu DR2XLAN
56 pages