What to do if the Yamaha 3FA-AE2 Motorcycle headlight or tail/brake light doesn't work?
If the headlight or tail/brake light on your Yamaha Motorcycle fails to light, check the fuse, battery, main switch, light switch, and wiring connections of the entire lighting system to identify and resolve the issue.
What to do if Yamaha 3FA-AE2 Motorcycle fuse is not working?
If the fuse in your Yamaha Motorcycle is not working, replace it with a new one.
What to do if Yamaha Motorcycle light switch faulty?
If the light switch on your Yamaha Motorcycle is faulty, replace the left handlebar switch.
What to do if Yamaha 3FA-AE2 Motorcycle main switch not working?
If the main switch on your Yamaha Motorcycle is not working, replace it.
Explains the structure and organization of the service manual.
Details the use and components of exploded diagrams for disassembly.
Indicates chapter subjects found on the top right of each page.
Identifies specifications appearing within the text of the manual.
Illustrates types of lubricants and their specific application points.
Indicates where to apply locking agents and when to install new parts.
Details the physical measurements of the YFM125S model, including length, width, and height.
Provides dry, wet, and maximum load specifications for the vehicle.
Lists fuel type, tank capacity, and reserve amount for the YFM125S.
Covers electrical specifications like ignition, generator, battery, and lighting.
Specifies the type and recommended gap for the spark plug.
Lists detailed specifications for the carburetor, including jets and settings.
Details specific torque values for tightening chassis components.
Specifies C.D.I. unit model and pickup coil resistance.
Details charging system specifications like magneto and coil resistance.
Lists rectifier/regulator type and capacity.
Provides data for the starter motor and starter relay.
Identifies circuit breaker type and amperage ratings.
Illustrates routing paths for various cables and wires on the vehicle.
Provides step-by-step guidance for proper cable management and securing.
Details removal/installation for seat, front carrier, bumper, and center cover.
Details the steps for removing the front grill assembly and front fender.
Identifies individual parts for removal and installation.
Identifies parts for removal and installation of rear carrier and fender.
Provides a caution for disconnecting battery leads during removal.
Instructions for adjusting the vertical aim of the headlight beams.
Step-by-step guide for removing and replacing the headlight bulb.
Detailed wiring diagram for the ignition system.
Detailed wiring diagram for the charging system.
Detailed wiring diagram for the lighting system.
Guides for diagnosing and resolving lighting system failures.
Procedures to check fuses, main switch, and light switch continuity.
Procedure to check the battery condition and voltage.
Detailed wiring diagram for the signal system.
Steps to check horn switch continuity and voltage.
Procedure to measure voltage at the horn terminal.
Explains the structure and organization of the service manual.
Details the use and components of exploded diagrams for disassembly.
Indicates chapter subjects found on the top right of each page.
Identifies specifications appearing within the text of the manual.
Illustrates types of lubricants and their specific application points.
Indicates where to apply locking agents and when to install new parts.
Details the physical measurements of the YFM125S model, including length, width, and height.
Provides dry, wet, and maximum load specifications for the vehicle.
Lists fuel type, tank capacity, and reserve amount for the YFM125S.
Covers electrical specifications like ignition, generator, battery, and lighting.
Specifies the type and recommended gap for the spark plug.
Lists detailed specifications for the carburetor, including jets and settings.
Details specific torque values for tightening chassis components.
Specifies C.D.I. unit model and pickup coil resistance.
Details charging system specifications like magneto and coil resistance.
Lists rectifier/regulator type and capacity.
Provides data for the starter motor and starter relay.
Identifies circuit breaker type and amperage ratings.
Illustrates routing paths for various cables and wires on the vehicle.
Provides step-by-step guidance for proper cable management and securing.
Details removal/installation for seat, front carrier, bumper, and center cover.
Details the steps for removing the front grill assembly and front fender.
Identifies individual parts for removal and installation.
Identifies parts for removal and installation of rear carrier and fender.
Provides a caution for disconnecting battery leads during removal.
Instructions for adjusting the vertical aim of the headlight beams.
Step-by-step guide for removing and replacing the headlight bulb.
Detailed wiring diagram for the ignition system.
Detailed wiring diagram for the charging system.
Detailed wiring diagram for the lighting system.
Guides for diagnosing and resolving lighting system failures.
Procedures to check fuses, main switch, and light switch continuity.
Procedure to check the battery condition and voltage.
Detailed wiring diagram for the signal system.
Steps to check horn switch continuity and voltage.
Procedure to measure voltage at the horn terminal.
General| Brand | Yamaha |
|---|---|
| Model | 3FA-AE2 |
| Category | Motorcycle |
| Language | English |
To Next Page