Why can I only hear sound from one speaker on my Yamaha A-S3000 Amplifier?
If you only hear sound from one speaker connected to your Yamaha Amplifier, first, check that all cable connections are correct and secure; if the problem continues, the cables may be defective. Second, verify that the BALANCE control is set to the appropriate position.
What to do if the sound suddenly goes off on my Yamaha Amplifier?
If the sound suddenly goes off on your Yamaha Amplifier, the protection circuitry may have been activated due to a short circuit. Check that the speaker wires are not touching each other or shorting out against the rear panel of the unit, and then turn the power back on.
Why is the INPUT indicator flashing on my Yamaha A-S3000?
If the INPUT indicator on the front panel of your Yamaha Amplifier flashes and the volume is turned down when you turn it on, the protection circuitry may have been activated because of a short circuit. Check that the speaker wires are not touching each other or shorting out against the rear panel of the unit, and then turn the power back on.
Why can't I adjust the volume level on my Yamaha Amplifier?
If the volume level cannot be adjusted on your Yamaha Amplifier, it might be because MAIN DIRECT is selected as the input source. If so, adjust the volume on the connected component. Alternatively, connect the external component to input jacks other than MAIN IN and select the corresponding input source.
Why is there a lack of bass and ambience on my Yamaha Amplifier?
If you notice a lack of bass and no ambience with your Yamaha Amplifier, check that the + and – wires are connected correctly at both the amplifier and the speakers. Ensure the speaker wires are connected to the correct + and – phase.
Why is the volume level low when playing a record on my Yamaha A-S3000 Amplifier?
General| Damping factor | 250 |
|---|---|
| Amplifier class | - |
| Input sensitivity | 200 mV |
| Audio output channels | - channels |
| Peak power per channel | 300 W |
| Signal-to-Noise Ratio (SNR) | 103 dB |
| Total Harmonic Distortion (THD) | 0.025 % |
| Dynamic power per channel (4 Ohm) | 200 W |
| Dynamic power per channel (6 Ohm) | 150 W |
| Dynamic power per channel (8 Ohm) | 120 W |
| Speakers connectivity type | Clamp terminals |
| Purpose | Home |
| Product color | Black, Silver |
| Connectivity technology | Wired |
Weight and Dimensions| Depth | 464 mm |
|---|---|
| Width | 435 mm |
| Height | 180 mm |
| Weight | 24600 g |
Explains Yamaha's approach to audio quality, inspired by piano craftsmanship.
Chronological overview of Yamaha's audio product development from the 1920s to the 2010s.
Details the operation and purpose of all controls located on the front panel of the A-S3000.
Explains the various input/output jacks, switches, and connectors on the rear panel of the A-S3000.
Covers the functions and usage of the supplied remote control for operating the A-S3000.
Provides step-by-step instructions for inserting batteries into the remote control unit.
Details on connecting speakers using bare wire, banana plugs, Y-lugs, and bi-wiring methods.
Instructions for connecting the power cable and system control/trigger cables.
Guide to connecting various audio sources via RCA and balanced XLR inputs.
Detailed technical data on power output, input sensitivity, impedance, and tone control ranges.
Information on power supply, consumption, dimensions, weight, and overall performance.
Graphical representations of tone control characteristics and total harmonic distortion.
A guide to identifying and resolving common issues encountered during unit operation.
Instructions on how to clean and maintain the finish and components of the A-S3000.
Essential guidelines for safe operation, installation, and handling of the A-S3000 unit.
Details on FCC requirements, compliance statements, and notices for US and Canadian customers.
Crucial advice on installation, environment, handling, and electrical safety before operating the unit.
To Next Page
