EasyManuals Logo

Yamaha CS2x Service Manual

Yamaha CS2x
54 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #22 background imageLoading...
Page #22 background image
CS2X
22
04 SW LED
Scen2
When the next check is ready, the LCD indicates the
next check switch. If there is a corresponding LED, it
blinks. When the check switch is pressed and the result
of the check is good, a beep will sound and the blinking
LED will go out, if applicable. Then the next check is
ready and the LCD will indicate the switch. If a switch
that the LCD is not indicating is pressed, the check will
be ignored and the status will not change. When all the
switch checks have finished and all the results have been
good, the LCD will indicate “OK”.
DISPLAY OF THE RESULTS
OK 04 SW LED
OK
NG (No change in display message)
TEST END
After displaying “OK” of the test result above, the test
will end and proceed to the next test.
T5. MIDI TEST
05 MIDI
After connecting the MIDI IN to the MIDI OUT via a
MIDI cable, execute the test. If the MIDI IN/OUT check
is good, “OK” will be displayed on the LCD and the test
pattern MIDI code (AA FF 00 55) will be transmitted
from the MIDI THRU.
DISPLAY OF THE RESULTS
OK 05 MIDI
OK
NG 05 MIDI
err
TEST END
When the test result is displayed on the LCD, the test
will end. If the test result is “OK”, the test will proceed
to the next test.
T6. HOST SELECT SWITCH TEST
06 HOST SEL
Mac
If the [HOST SELECT] switch has been set at the [MAC]
position, set the switch at the other position and return
it to the [MAC] position again.
Switch the [HOST SELECT] from [Mac] to [MIDI],
according to the order indicated on the LCD.
If the switch is OK, a beep wave will sound.
DISPLAY OF THE RESULTS
OK 06 HOST SEL
OK
NG (No change in display message)
TEST END
If the switch is OK at all positions, “OK” is displayed
and the test will end.
T7. TO HOST TEST
07 TO HOST
HstSW
This test is only utilized at the factory and it is not
intended for field service use.
When the test enters this test, the LCD will display “NG”.
Press the [PERFORMANCE] switch, then use the
PROGRAM [+] and PROGRAM [-] switches to select
anther test.
T8. WAVE ROM TEST
08 WAVE
Performs a read test of WAVE ROMs.
DISPLAY OF THE RESULTS
OK 08 WAVE
OK
NG 08 WAVE
NG
TEST END
This test ends after displaying the result.
T9. 1k Hz SOUND OUTPUT (OUTPUT L) TEST
09 OUT L
Check that the correct signal is output from the OUTPUT
L and PHONES (L) jacks.

Other manuals for Yamaha CS2x

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yamaha CS2x and is the answer not in the manual?

Yamaha CS2x Specifications

General IconGeneral
Polyphony64 voices
Multitimbral Capacity16 parts
LFO2 LFOs per voice
Keyboard61 keys
Velocity SensitivityYes
AftertouchNo
ControlPitch bend, Modulation wheel
Weight6.5 kg
Year Released1998
TypeSynthesizer
OscillatorsAWM2
FilterResonant filter
EffectsReverb, Chorus, Variation
StorageInternal memory for patches
MIDIIn, Out, Thru
OutputsStereo output, Headphone output
InputsSustain pedal, Foot controller
Memory128 user voices
ConnectionsMIDI (In/Out/Thru), Foot Controller, Foot Switch

Related product manuals