EasyManuals Logo

Yamaha HTR-6295 User Manual

Yamaha HTR-6295
182 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #35 background imageLoading...
Page #35 background image
31 En
English
INTRODUCTION
ADDITIONAL
INFORMATION APPENDIX
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
The FM/AM tuner of this unit provides the following two
modes for tuning.
Frequency tuning mode
You can tune into a desired FM/AM station by searching
or specifying its frequency.
Preset tuning mode
You can preset the frequencies of FM/AM stations by
registering them to specific numbers, and later just select
those numbers to tune in.
Note
Adjust the FM/AM antennas connected to this unit for the best reception.
1 Rotate the TINPUT selector (or press
dTUNER) to select “TUNER” as the input
source.
2 Press HBAND (or eFM or eAM) to select a
band.
3 Press ITUNING l / h (or eTUNING k /
n) to specify the frequency.
The TUNED indicator on the front panel display
lights up when the tuner is tuned into a station. The
STEREO indicator also lights up if the program being
broadcasted is in stereo.
The frequency changes in the following manner according
to how you press ITUNING l / h (or eTUNING
k / n).
When you press the key more than 1 second
The tuner searches the frequency of a station that is
detectable around the current frequency. This is effective
when the tuner can receive strong signals without any
interference. Once the search starts, release the key.
When you keep holding the key, the search continues even
when a station is detected. This is useful when you want to
tune into a specific station.
When you press and release the key
The tuner increases or decreases the frequency in steps.
Use this method when the tuner cannot receive strong
signals and stations are skipped during the search.
y
You can switch between stereo and monaural for FM broadcast in the
Option menu (page 42).
4 To tune in by direct frequency tuning, press
lNumeric keys to enter the frequency of
the station.
Enter only integers. For example, if you want to set
the frequency to 88.9 MHz, enter “889”.
Notes
When you press lNumeric keys during preset tuning, a
preset number is selected. Set tuning mode to frequency tuning
mode using ITUNING l / h (or eTUNING k / n) prior to
the operation.
“Wrong Station!” appears on the front panel display when you
enter a frequency that is out of receivable range. Make sure that the
entered frequency is correct.
You can register up to 40 FM/AM stations (Preset).
The tuner automatically detects FM stations with strong
signals and registers up to 40 stations. To register AM
stations, use manual station preset.
1 Rotate the TINPUT selector (or press
dTUNER) to select “TUNER” as the input
source.
2 Press sOPTION on the remote control.
The Option menu for “TUNER” is displayed
(page 41).
3 Select “Auto Preset” and then press
jENTER.
Automatic station preset starts about 5 seconds later
from the lowest frequency upwards.
FM/AM tuning
Tuning into the desired FM/AM station
(Frequency tuning)
STEREO
TUNED
FM92.5MHz
Registering FM/AM stations and
tuning in (Preset tuning)
Registering stations by automatic station
preset
Auto Preset

Table of Contents

Other manuals for Yamaha HTR-6295

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Yamaha HTR-6295 and is the answer not in the manual?

Yamaha HTR-6295 Specifications

General IconGeneral
Channels7.2
Frequency Response10 Hz - 100 kHz
Response Bandwidth10 Hz - 100 kHz
Signal-To-Noise Ratio100 dB
Input Impedance47 kΩ
Audio D/A Converter192kHz/24-bit
Tuner Presets40
Surround SoundYes
BluetoothNo
Wi-FiNo
InputsDigital optical, Digital coaxial, Analog audio
OutputsHDMI
HDMIYes
Input Sensitivity200 mV
Surround Sound EffectsDolby Digital, DTS
DSP Presets17
Output Impedance / Channel8 Ω
Video Inputs/OutputsHDMI
Audio Inputs/OutputsAnalog audio, digital coaxial, digital optical, HDMI
Dimensions (W x H x D)435 mm

Related product manuals