Why do surround speakers have no sound on my Yamaha RX-V450 Receiver?
If there is no sound from the surround speakers connected to your Yamaha Receiver: * Increase the output level of the surround speakers. * Select the appropriate setting for the surround left and right speakers in “SURR LR” in SET MENU. * If playing a monaural source, press STRAIGHT to turn on the sound fields.
Why is there no sound from the subwoofer on my Yamaha RX-V450?
If there is no sound from the subwoofer connected to your Yamaha Receiver: * If playing a Dolby Digital or DTS signal, ensure “BASS OUT” in SET MENU is set to SWFR or BOTH. * If playing a 2-channel source, select BOTH for “BASS OUT” in SET MENU.
What to do if the sound suddenly goes off on Yamaha Receiver?
If the sound from your Yamaha Receiver suddenly cuts off: * Check that the impedance selector setting is correct. * If the sleep timer turned the unit off, turn the power back on. * Ensure the receiver is not muted by pressing the MUTE button.
Why is my Yamaha RX-V450 remote not working?
If the Yamaha Receiver's remote control isn't working correctly, ensure you're within 6 meters (20 feet) and no more than 30 degrees off-axis from the front panel. Replace all the batteries, if they are weak. Also, check that the manufacturer code is correctly set using the 'LIST OF MANUFACTURER CODES'.
How to fix no sound on Yamaha RX-V450?
If you're not getting any sound from your Yamaha Receiver, try these steps: * Check and properly connect all input and output cables; the cables may be defective. * Ensure the input mode is set to AUTO, not DTS or ANALOG. * Select the correct input source using the INPUT, MULTI CH INPUT, or input selector buttons. * Make sure the speaker connections are secure. * Select the appropriate front speakers with SPEAKERS A and/or B. * Increase the volume and ensure the receiver is not muted by pressing MUTE. * If playing a DTS signal, set the input mode to AUTO or DTS. * Confirm that the source signals can be reproduced by the unit.
Why does my Yamaha RX-V450 suddenly turn into standby mode?
If your Yamaha Receiver suddenly turns into standby mode, it's likely because the internal temperature became too high, activating the overheat protection circuitry. Wait about 1 hour for the unit to cool down before turning it back on.
How to fix Yamaha Receiver remote control that is not working?
If your Yamaha Receiver remote control isn't working, consider these potential solutions: * Ensure you're within a 6 m (20 ft) range and within 30 degrees off-axis from the front panel. * Reposition the unit if direct sunlight or lighting is interfering with the remote control sensor. * Replace all the batteries. * Set the manufacturer code correctly using the “LIST OF MANUFACTURER CODES”. * Try another code for the same manufacturer using the “LIST OF MANUFACTURER CODES”.
What to do if my Yamaha RX-V450 fails to turn on?
If your Yamaha Receiver fails to turn on or enters standby mode shortly after being powered on, there might be several reasons: * Ensure the power cord is firmly connected. * Verify the impedance setting matches your speakers. * Check speaker wire connections for any shorts that may have activated the protection circuitry. * If the unit experienced a strong electric shock, put it in standby mode, unplug it for 30 seconds, and then plug it back in.
Why does my Yamaha RX-V450 suddenly turn off?
If your Yamaha Receiver suddenly turns into standby mode, it may be due to overheating. Wait about 1 hour for the unit to cool down before turning it back on.
How to fix a Yamaha Receiver remote control that is not working?
If the remote control for your Yamaha receiver isn't working properly: * Ensure you are within 6 meters (20 feet) and no more than 30 degrees off-axis from the front panel. * Reposition the unit if direct sunlight or lighting is interfering with the remote control sensor. * Replace the batteries. * Set the manufacturer code correctly.
General| Channels | 6.1 |
|---|---|
| Signal-to-Noise Ratio | 100 dB |
| Input Impedance | 47 kOhm |
| Input Sensitivity | 200 mV |
| Audio D/A Converter | 24-bit/192 kHz |
| Surround System Class | 6.1 channel |
| Digital Sound Processor (DSP) | Yes |
| Tuner Bands | AM/FM |
| Preset Station Qty | 40 |
| Frequency Response | 10Hz-100kHz |
| Total Harmonic Distortion | 0.06 % |
| Inputs | 4 x Audio |
| Outputs | 1 x Audio (RCA), 1 x Video (Composite) |
| Built-in Decoders | Dolby Digital, DTS |
| Surround Sound Effects | Dolby Pro Logic II |
| Tuning Range | FM: 87.5 - 108 MHz |
| Connector Type | RCA |
| Amplifier Output Details | 85 W (Front), 85 W (Center), 85 W (Surround), 85 W (Surround Back) |
| DSP Presets | 7ch stereo, Concert hall, Disco, Game, Jazz club, Movie, Stadium |
To Next Page
