Yamato SM530 - User Manual

Questions and Answers

K
kevinwatsonAug 17, 2025
Why won't the sterilization temperature or pressure rise in my Yamato Laboratory Equipment?
- C
  Christine KleinAug 17, 2025
  If the sterilization temperature or pressure inside the chamber of your Yamato Laboratory Equipment isn't rising, several factors could be at play. It could be that the preset value is lower than the current temperature inside the chamber, in which case you should adjust the preset value. Also, verify that the power supply voltage is adequate and that the ambient temperature isn't too low. Ensure the cover is securely closed and inspect the packing or flange for any damage.
S
Stephanie Schneider DVMAug 20, 2025
How to troubleshoot a Yamato Laboratory Equipment that won't start?
- D
  douglasisaacAug 20, 2025
  If your Yamato Laboratory Equipment isn't starting even with the leakage breaker on, make sure the power cable is properly connected to the power supply. Also, check to see if there is a power outage or if the power voltage is correct.
J
Jeffrey PriceAug 22, 2025
What to do if too much vapor blows out of my Yamato Laboratory Equipment?
- D
  Donald SimmonsAug 22, 2025
  If your Yamato Laboratory Equipment is expelling too much vapor or hot water from the drain bottle, check the cooling water box to ensure it contains water and that the water isn't hot. Make sure the exhaust hose isn't removed or broken, the silicon plug is securely fitted, and the water level in the cooling water box is not above the drain level.
C
Charles ShieldsAug 26, 2025
Why does the temperature change during operation of my Yamato Laboratory Equipment?
- T
  theresakingAug 26, 2025
  If the temperature fluctuates during operation of your Yamato Laboratory Equipment, ensure that an adequate preset temperature is set. Also, check the power supply voltage and the ambient temperature to see if variations are too large.
M
martinjenniferAug 28, 2025
What causes exhaust failure in Yamato Laboratory Equipment?
- T
  thompsonkariAug 28, 2025
  If you're experiencing exhaust failure or the safety valve is activated on your Yamato Laboratory Equipment, check the hose to the cooling water box for any twists or clogs. Also, inspect the exhaust outlet inside the chamber to ensure it isn't blocked by sterile samples and verify that you haven't stored too many samples.
J
Justin MorrowAug 31, 2025
What to do if the cover of my Yamato Laboratory Equipment does not open?
- M
  Michael LynchAug 31, 2025
  If the cover of your Yamato Laboratory Equipment won't open, first ensure that the power is turned on. If it is, check whether the sterilization process has been completed. If not, wait for it to finish.
S
Stacy ThompsonSep 2, 2025
Why is pressure rising in my Yamato Laboratory Equipment chamber when the solenoid valve is open?
- B
  barbara39Sep 2, 2025
  If the pressure inside the chamber of your Yamato Laboratory Equipment rises even when the solenoid valve is open, check the exhaust outlet inside the chamber to ensure it is not blocked.
R
Rachel HallSep 5, 2025
Why does my Yamato Laboratory Equipment halt in standby state?
- P
  Patrick HartmanSep 5, 2025
  If your Yamato Laboratory Equipment halts in standby state, ensure that the cover is securely closed.
W
wbassSep 8, 2025
Why is my Yamato Laboratory Equipment leaking water?
- A
  ashley72Sep 8, 2025
  If your Yamato Laboratory Equipment is leaking water, check to make sure the drain valve is securely closed.
R
Robert WiseSep 12, 2025
Why is my Yamato Laboratory Equipment making a large noise during air purge?
- B
  bproctorSep 12, 2025
  If your Yamato Laboratory Equipment is making a lot of noise during air purge, verify that the silencer is installed. Also, check the connection of the silencer inside the cooling water box.