Yamato SM830 - User Manual

Questions and Answers

A
alvarezkarenAug 17, 2025
Why won't the sterilization temperature or pressure rise in my Yamato Laboratory Equipment?
- M
  Michael Davis MDAug 17, 2025
  If the sterilization temperature or pressure inside the chamber of your Yamato Laboratory Equipment isn't rising, several factors could be at play. It could be that the preset value is lower than the current temperature inside the chamber, in which case you should adjust the preset value. Also, verify that the power supply voltage is adequate and that the ambient temperature isn't too low. Ensure the cover is securely closed and inspect the packing or flange for any damage.
G
glen50Aug 20, 2025
How to troubleshoot a Yamato Laboratory Equipment that won't start?
- H
  howellmatthewAug 20, 2025
  If your Yamato Laboratory Equipment isn't starting even with the leakage breaker on, make sure the power cable is properly connected to the power supply. Also, check to see if there is a power outage or if the power voltage is correct.
C
crossjavierAug 22, 2025
What to do if too much vapor blows out of my Yamato Laboratory Equipment?
- R
  rebecca37Aug 22, 2025
  If your Yamato Laboratory Equipment is expelling too much vapor or hot water from the drain bottle, check the cooling water box to ensure it contains water and that the water isn't hot. Make sure the exhaust hose isn't removed or broken, the silicon plug is securely fitted, and the water level in the cooling water box is not above the drain level.
E
Emily SextonAug 26, 2025
Why does the temperature change during operation of my Yamato Laboratory Equipment?
- C
  Christina WilliamsAug 26, 2025
  If the temperature fluctuates during operation of your Yamato Laboratory Equipment, ensure that an adequate preset temperature is set. Also, check the power supply voltage and the ambient temperature to see if variations are too large.
J
John RodgersAug 28, 2025
What causes exhaust failure in Yamato Laboratory Equipment?
- J
  johnathan83Aug 28, 2025
  If you're experiencing exhaust failure or the safety valve is activated on your Yamato Laboratory Equipment, check the hose to the cooling water box for any twists or clogs. Also, inspect the exhaust outlet inside the chamber to ensure it isn't blocked by sterile samples and verify that you haven't stored too many samples.
S
smithheatherAug 30, 2025
What to do if the cover of my Yamato Laboratory Equipment does not open?
- C
  christopher83Aug 30, 2025
  If the cover of your Yamato Laboratory Equipment won't open, first ensure that the power is turned on. If it is, check whether the sterilization process has been completed. If not, wait for it to finish.
J
Jordan BrownSep 2, 2025
Why is pressure rising in my Yamato Laboratory Equipment chamber when the solenoid valve is open?
- K
  Kristina LaneSep 3, 2025
  If the pressure inside the chamber of your Yamato Laboratory Equipment rises even when the solenoid valve is open, check the exhaust outlet inside the chamber to ensure it is not blocked.
J
james94Sep 5, 2025
Why does my Yamato Laboratory Equipment halt in standby state?
- K
  Kristin AndrewsSep 5, 2025
  If your Yamato Laboratory Equipment halts in standby state, ensure that the cover is securely closed.
M
Matthew AbbottSep 7, 2025
Why is my Yamato Laboratory Equipment leaking water?
- M
  Michael BaxterSep 8, 2025
  If your Yamato Laboratory Equipment is leaking water, check to make sure the drain valve is securely closed.
M
Michael ThompsonSep 12, 2025
Why is my Yamato Laboratory Equipment making a large noise during air purge?
- S
  sean46Sep 12, 2025
  If your Yamato Laboratory Equipment is making a lot of noise during air purge, verify that the silencer is installed. Also, check the connection of the silencer inside the cooling water box.

Summary

Safety Precautions

Meaning of Illustrated Symbols

Table of Illustrated Symbols

Visual guide to warning, caution, prohibit, and compulsion symbols.

Before Using

Installation Precautions

Guidelines for proper installation site selection and setup.

Preparation Before Operation

Steps for preparing the unit before starting operation.

Operation Method

Operation Modes Overview

Lists and describes available operation modes.

Equipment Function List

Liquefy & Retain Temp. Operation

Step-by-step guide for the liquefy & retain temp. operation.

Sterilization Operation Procedures

Step-by-step guide for sterilize & retain temp. operation.

Drying Operation Procedures

Step-by-step guide for instrument drying.

Shortcut Functions Guide

Handling Precautions

Flammable Material Safety

Safety precautions for handling flammable solvents and materials.

General Operational Safety

Maintenance Method

Daily Inspection and Maintenance

Routine checks for safe and reliable operation.

In the Event of Failure

Safety Device and Error Codes

Lists error codes, their causes, and solutions.

Troubleshooting Common Issues

Guide to diagnose and resolve operational problems.

After-sales Service and Warranty

Requesting Repairs and Support

How to contact for service and warranty information.

List of Dangerous Substances

Explosive Substances to Avoid

Flammable Substances to Avoid

Maintenance and Replacement

Pressure Gauge and Safety Valve Maintenance

Regular Spot Check

Small Pressure Container Self-Checking

Periodic inspection guidelines for the pressure container.

Detailed Check Procedures

Piping, Pressure, and Temp. Accuracy Checks

Yamato SM830 Specifications

General

Model	SM830
Light Source	LED
Type	Microscope
Magnification	40x-1000x
Stage	Mechanical
Condenser	Abbe
Eyepiece	WF10x
Objective Lenses	4x, 10x, 40x, 100x
Power Supply	AC 100~240V