L3-05 ............................................ 238
L3-06 ........................................160, 238
L3 Stall Prevention Function ...................... 237
L4-01 ............................................ 238
L4 Frequency Detection ........................... 238
L5-01 ........................................150, 239
L5 Fault Reset.................................... 239
L6-01 ............................................ 239
L6-02 ........................................150, 239
L6-03 ........................................150, 239
L6 Overtorque Detection .......................... 239
L8: Hardware Protection .......................... 239
L8-01 ............................................ 239
L8-05 ............................................ 240
L8-10 ............................................ 240
L8-12 ........................................220, 240
L8-18 ............................................ 240
L8-29 ............................................ 220
L8-38 ........................................163, 240
LED Check ..................................118, 245
LED Operator ...........................26, 80, 81, 96
LF ...........................................134, 140
LO/RE.................................... 82, 91, 121
LOCAL............................................91
Local/Remote Run Selection....................... 224
Local/Remote Selection ........................... 232
Low Voltage Directive ............................ 255
Low Voltage Wiring .............................. 271
L Protection Function ............................. 237
M
Magnetic Flux Compensation Capacity ............. 225
Main Circuit Connection Diagram ...............46, 56
Main Circuit Terminal Functions.....................50
Main Circuit Terminal Power Supply.................54
Main Circuit Terminals Connection ..................46
Main Circuit Terminal Wiring ..................28, 265
Main Frequency Reference ..........................67
Main Frequency Reference Input.....................58
Maintenance Alarms .............................. 176
Master Speed Reference Lower Limit .............. 228
Maximum Motor Size Allowed (kW)...........211, 213
Maximum Output Frequency ...................... 230
Maximum Output Voltage ........................ 230
MEMOBUS/Modbus Communication Error ...134,
135,
137, 147
MEMOBUS/Modbus Communications Test Mode
Complete ........................................ 150
MEMOBUS/Modbus Communications Test Mode Error
.................................................. 150
MEMOBUS/Modbus Error Code .................. 244
Memobus/Modbus Error Code ..................... 118
MEMOBUS/Modbus Test Mode Complete ......... 135
Middle Output Frequency ......................... 230
Middle Output Frequency Voltage ................. 230
Mid Output Voltage A ............................ 131
Minimum Output Frequency..............163, 164, 230
Minimum Output Frequency Voltage .............. 230
Minimum Output Voltage ......................... 131
Minor Alarms .................................... 134
Minor Faults .................................133, 134
Modes .............................................85
Momentary Power Loss Operation Selection ........ 237
Monitor Output .....................................59
Motor Does
Not
Operate
When
an
External
Run Command
is Input .......................................... 163
Motor Does Not Operate When the RUN Button on the
Digital Operator is Pressed ........................ 163
Motor Does Not Rotate............................ 157
Motor Hunting and Oscillation Control Parameters .. 132
Motor Hunting Occurs When Operating With a Light Load
.................................................. 161
Motor is Too Hot ................................. 159
Motor Line-to-Line Resistance.................111, 231
Motor No-Load Current .......................111, 231
Motor Overload ..............................134, 142
Motor Overload Protection Selection ...... 114, 237, 272
Motor Overload Protection Time.......... 114, 237, 273
Motor Parameters................................. 110
Motor protection operation time ................... 115
Motor Rated Current ................ 111, 114, 230, 272
Motor Rated Slip .............................111, 231
Motor Rotates After the Drive Output is Shut Off ... 162
Motor Rotates Faster Than the Frequency Reference. 160
Motor Rotates in One Direction Only............... 164
Motor Stalls During Acceleration or With Large Loads ...159
Motor Stops During Acceleration or When a Load is
Connected........................................ 164
Motor Wiring ......................................54
Multi-Function Analog 1 (Terminal AM Monitor
Selection) ........................................ 235
Multi-Function Analog Outputs .................... 111
Index
YASKAWA ELECTRIC TOEP C710606 25D YASKAWA AC Drive J1000 Installation & Start-Up Manual
281
To Next Page
Loading...
Need help?
General
