INDEX (Conttd)
Subject
Chapter
Par.
Page
D
DISPLAYING AND WRITING PARAMETERS .......................... 4 ........ 4.3.7 ..... 17o
Displayingand WritingParameters
.................................
4
........ 4,3.7.3 ... 171
DISPLAYING AND WRITING SETTING DATA (SETTING) ............ 4 ........ 4,3.6 ..... 168
DISPLAYING AND WRITING TOOL OFFSET DATAt
.................
4
........ 4.3.5 ..... 166
DISPLAYING STATUS INPUT/OUTPUT SIGNALS
...................
4 ........ 4.3.8 ..... 172
Displayin Memory Run Mode (PROGRAM
DISPLAY LOCK/MACHINE LOCK SWITCH
DRY RUN SWITCH
......................
DWELL (G04).o.....................o....
E EDIT
...................................
EDIT KEYS
.............................
MEM]) ................... 4 ........ 4.3.3.2 ... 160
..........................
5
........ 5.1.19 .... 193
..........................
5 ........ 5.1.18 .... 193
2
.......................... ........
2.8.5 ..... 29
4
.......................... ........
4.6
........ 180
..........................
4
........ 4.1.10 .... 154
EDIT LOCK SWITCH
............................................... ........
5
5.1,22
.... 194
EIA/ISO AUTO RECOGNITION ...................................... 3 ........ 3.1,2 ..... 148
EMERGENCY STOP PUSHBUTTON
..................................
5 ........ 5.1.4 ..... 189
ERROR DETECT OFF POSITIONING (G06) .............4............ 2 ........ 2.8.2.2 ... 27
Example of FS Editing
............................................. ........
5
5.1.31.6 .. 197
Example of High-speed M Function Processing
......................
2
........ 2.7.8.4 ... 23
Exercisesof Macro Programs
2
...................................... ........
2.8.23.11.. 89
F
Facing Cycle B (G94)
..............................................
2
........ 2.8.26,3 .. 121
FEED FUNCTION (F- AND E-FUNCTION)
2
.......................... ........
2.4.2
10
FEED HOLD PUSHBUTTON AND LAMP
.....
.............................
5 ........ 5.1.3 ..... 188
FEED/MINUTE AND FEED/REVOLUTION SWITCHOVER .............. 2 ........ 2,8.28 .... 124
Feed Per Minute (G98 Mode)
....................................... ........
2 2.4.2.2 ... 12
Feed Per Revolution(G99 Mode)
...................................
2
........ 2.4.2.1 ... 11
FEEDRATE OVERRIDE CANCEL SWITCH
...........................
5 ........ 5.1.12
... 192
FinishingCycle (G70)
.............................................
2
........ 2.8.25.5... 106
FS AUTOMATIC EDITING FUNCTION
...............................
5 ........ 5.1.31..... 196
FUNCTION KEYS
..................................................
4
........ 4.1.3 ..... 152
Functions
......................................................... 2
........ 2.6.5.2 ... 17
Functions
.........................................................
5 ........ 5.1.31.3... 196
G General
...........................................................
2
........ 2,8.25.1... 94
General
........................................................... ........
5 5.1.8.2
... 190
General
...........................................................
5 ........ 5,1.31.1... 196
General
...........................................................
5 ........ 5.2.3.10... 206
GENERAL PROGRAM FORM
......................................... ........
3
3.2.2
...... 148
G50 POINT RETURN SWITCHt
.....................................
5
........ 5.1.24 .... 195
G50 POINT RETURNt
..............................................
5 ‘-------5.2.4 ..... 208
GROOVE WIDTH COMPENSATION (G150, G151)*..................... 2 ........ 2.8,32
.... 147
Grooving in X-Axis (G75) .......................................... 2 ........ 2.8.25.7... 108
H
HANDLE AXIS SELECT SWITCH+ ................................s.. 5 ........ 5.1.6...... 189
HANDLE DIAL+ (MANUAL PULSE GENERATOR)
....<...............
5 ‘-------5.1.5 ----- 189
HANDLE DIALS FOR SIMULTANEOUS CONTROL OF
UP TO TWO AXESt
..........................................
5
..-.-... 5.1.8 ..4-. 189
Handle InterpolationFunction
......................................
5
.....+..5,1,8.1---- 190
HIGH-SPEED M FUNCTION
........................................ ........
2
2.7.8
.....
22
I Improved MultipleRepetitiveCycle Function........................ 2 ........ 2.8.25.10.. 115
INCH/METRIC DESIGNATION BY G CODE (G20, G21)t
2
............. ........
2.8.8
......
33
Input/Output ...................................................... 5 ........ 5.1.31.2... 196
I/OChannel ...................................................... 2 ........ 2.7.8.1 ... 22
INPUTTING SETTING DATA AND PARAMETER DATA
4
.............. ........
4.4.5
..... 178
INPUTTING TOOL OF OFFSET DATA INTO MEMORY
...............
4
........ 4.4.4 ..... 177
Input Unit andl O Times Input Unit ............................... 2 ........ 2.3.3.1.... 7
INSPECTION BEFORE TURNING ON POWER
........................
6 ........ 6,1 ....... 213
INTERLOCK INPUT (INTERLOCK)
.................................
5 ........ 5.1.23 .... 195
InternalToggle Switchesf
.........................................
4 ........ 4.3.6.2 ... 169
INTRODUCTION
...................................................
1
.....................
1
J
JOG FEEDRATE SWITCH AND FEEDRATE OVERRIDE SWITCH
.......
5
........ 5,1.10 ..... 191
JOG PUSHBUTTONS AND RAPID PUSHBUTTON
....................
5
........ 5.1.9 ..... 191
K KEEPING OF NC TAPE
............................................
3
........ 3.4.2 ..... 150
To Next Page
Loading...
Need help?
General
