INDEX
Subject
Chapter
Par.
A
ABSOLUTE AND INCREMENTAL INPUT S............................ 2 ........ 2.3.5
ABSOLUTE/INCREMENTAL PROGRAMl,41NG (G90,
G91)
2
. . . . . . . . . . . . . . . . . . . . . .
2.8.31
Accelerationand Decelerationof Rapid Traverse
and Manual Feed .......................................$......2 ........ 2.4.3.
ADDING PART PROGRAMS
.........................................
4
ADDRESS KEYS
“.””””.. 4.6.4
...................................................
4
.’””””””4.1.4
Page
. . . .
8
..”” 146
. . .
12
.,. .
181
. . . .
153
Address Search ....................................................4
........
ALARM CODE (ALM) DISPLAY
..................................... ........
4
Alarm Code Display
................................................ ........
4
Alarm Number of Microprograms ..................................2 ........
Argument Designation
.............................................. ........
2
4.3.3.4““”
4.3.9 -.O..
4.3.9.1-..
2.8.23.10-
2.8.23.2‘.
161
172
172
88
68
212
195
12
199
56
216
35
109
203
204
AUTO MODE HANDLE OFFSET
.....................................
5
........
AU TO MOD E HANDLE OFFSET SWITCHt ...................44......5
........
AUTOMATIC ACCELERATION AND DECELERATION ........0..0.....2 ........
AUTOMATIC COORDINATE SYSTEM SETTING+
5
..................... ........
AutomaticNose RFunction .........................................2
........
5.2.7 ‘----
5.1<28 ----
2.4.3
.....
5.2.2
.....
2.8.19.1..
AU TOMATIC OPERATION INMDI h40DE ...........................6 ........
AUTOMATIC RETURN TO REFERENCE POINT (G28)
2
................ ........
AutomaticThreading Cycle (G76) ...................................2
........
AutomaticWritingintothe Tool CoordinateMemory
5
................. ........
AutomaticWritingintothe Work CoordinateSystem
ShiftLIemory..................................................5 ........
6.8
.......
2.8.11 ....
2.8.25.8‘.
5.2.3.3 .“”
5.2.3.4 .“’
B
BUFFER REGISTER
................................................ ........
2
BUFFERING FUN CTION(M93, M92)t ..............................-2 ........
2.1.5 ..”””
2.7.3 .“”””
6
19
C CANNED CYCLES (G90, G92, G94) ................................ 2 ........
CHECKING REGISTERED PART PROGRAM NUMBER ................. 4
........
CircularArc MultipleCornering (G112).............................2 ........
CIRCULAR INTERPOLATION (G02, G03)
2
........................... ........
CIRCULAR PATH hfODE ON/OFF ON TOOL RADIUS COMPENSATION
(G97, L496)+
................................................. ........
2
COMMAND DATA DISPLAY ..........................................4 ........
2.8.26 ‘“””
4.6.1
.....
2,8.30.2..
2.8.4 .....
116
180
143
28
20
157
2.7.4 .....
4.3.2 .....
Command Data Display .............................................4
........
Command Pulse AccumulationRegisterDisplay
(COMMAND PULSE) ........................................... 4 ........
Conditionsfor the AutomaticNose R Compensation Function
to be Enabled ................................................ 2 ........
Conditionsof the Specificationsto Perform FS Editing.............. 5 ........
Considerationsand Remarks for Macro Programs ................... 2 ........
4.3.2.1 ...
158
4.3.4.9.. 165
2,8.19.2..
5.1.31.7..
2.8.23.9“.
56
198
84
CONSTANT DISPLAY .............................................. 4 ........
CONSTANT SURFACE SPEED CONTROL (G96, G97)t ............... 2 ........
ControlComma~ ds
................................................. ........
2
CoordinateSystem Setting(G50 X_. Z_. ) ........................ 5 ........
COORDINATE WORD S.............................................. 2 ........
4.3.1 .....
2.8.27..-.
2.8.23,6-.
5.2.3,5...
2.3
.......
156
123
81
205
7
COORDINATE WORDS .............................................. 2 ........
CORNERING (Gil, G12)+ ............ 2
............................... ........
CRT CHARACTER DISPLAY ........................................ 4 .......
CURRENT POSITION DISPLAY ..................................... 4 ........
CURSOR KEYS
.................................................... ........
4
2.3.1
.....
2.8.7
.....
4,1.2 ....-
4,3.4
.....
4.1.8
.....
7
31
152
162
154
CUTTING DEPTH OVERRIDE SWITCHt FOR G71 AND G72
5
.......... ........
CYCLE START PUSHBUTTON AND LAMP
.................
5
......... ........
5.1.29 ....
5.1.2 ....
195
188
153
6
182
D
DATA KEYS .......................................................4 ........
DECIMAL POINT PROGRAMMING
...................................
2
........
DELETING PART PROGRAM BLOCKS
4
............................... ........
Display and Deletingof RegisteredProgram Number
(PROGRAM NO. TABLEDR )t
.................................
4
.,.,....
Displayand Writeof Localand Common Variables
..................
2
........
4.1.5....
2.1.3 ...,.
4.6.5
.....
4.3.9.3 ...
2,8.23.8,.
173
83
156
158
159
161
180
DISPLAY AND WRITING OPERATION
...............................
4
........
Displayof Subprogram Run Status (SUB PROG . NESTING)
.........
4
........
Displayof Tool Life ControlUse Status (TOOL LIFE CONTROL) .... 4
........
Displayin EDIT Mode .............................................. 4
........
DISPLAYING AND CHECKING STORED PART PROGRAMS ...........
4
........
4.3
.......
4.3.2.2 ...
4.3.2.3 ...
4.3,3.3 ...
4.6.2
.....
To Next Page
Loading...
Need help?
General
