INDEX (Cent’d)
Subject
Chapter
Par.
Page
o
OPERATION IN TAPE AND MEMORY MODE 6
......................... ........
6.6 ....... 215
OperationProcedure
...............................................
5 ........ 5.1.31.4 .. 196
OPERATION PROCEDURE
..........................................
5 ........ 5.2 ....... 198
OPERATION PROCEDURE
.......................................... .....................
6
213
OperationTime Display ............................................ 4 ........ 4.3.9.4 ... 174
OPTIONAL
BLOCK SKIP (/1-/9)+
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 ........ 2.2.3
.....
7
OPTIONAL BLOCK SKIP SWITCH
..................................
5 ........ 5.1.17 .... 193
ORG (ORIGIN) KEYS
..............................................
4
........
4.1.9 ..... 154
OTHER M CODES
..................................................
2 ........ 2.7.6
.....
21
OUTPUTTING PART PROGRAM TO PAPER TAPE
...................
4 ........ 4.7.1 ..... 183
OUTPUTTING SETTING IPARAMETER DATA TO PAPER TAPE
......
4 ........ 4.7.3 ..... 184
OUTPUTTING TOOL OFFSETS TO PAPER TAPE
....................
4 ........ 4.7.2 ..... 184
Overview
.........................................................
2 ........ 2.6.5.1 ... 17
Overview of L4acroProgram Body .................................. 2 ........ 2.8.23.3 .. 69
P
PAGE KEYS
.......................................................
4 ........ 4.1.7 ...... 153
PAPER TAPE
..................................................~..
3 ........ 3,3.1 ..... 150
Parameter of Bit DisplayFormat
............................
.......
4 ........ 4.3.7.1 ... 171
Parameter of Decimal DisplayFormat 4
............................... ........
4.3.7.2
... 171
Parameters
.................
.......................................
2
........ 2.7.8.2 ... 22
Parameters ........................................................ 5 .......- 5.2.3.2 ‘o- 203
PART PROGRAM AND NC DATA OUTPUT OPERATIONS
...........
4
........
4.7 ....... 183
PatternRepeating (G73)
..........................................
2
........
2.8.25.4 .. 104
Peck Drillingin Z-axis (G74) ...................................... 2 ........ 2.8.25.6 .. 107
Position........................................................... 4 ........ 4.3.4,4 ..- 163
Position[ABSOLUTE]
..............................................
4
........ 4.3.4.2 ... 163
Position
[EXTERNAL I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 ........ 4.3.4.1 ... 162
Position(EXTERNAL) “O” Setting.................................. 5 ........
5,2.3.6 ... 205
Position[INCREMENT]
.............................................
4
........ 4.3.4,3 ... 163
POSITION (GOO, G06)
............................................. ........
2 2.8.2
.....
24
Positioning(GOO)
..................................................
2 ........ 2.8.2.1 ... 24
POSITION STORED PUSHBUTTON+ 5
................................ ........
5.1.30..... 196
POWER ON/OFF OPERATION
..............................
4
......... ........
4.2 ....... 155
POWER ON IOFF PUSHBUTTONS ................................... 4
........
4.1.1
..... 152
Precautionsin Programming G70 through G76 ...................... 2 ........ 2.8.25.9... 112
PREPARATION FOR STORED LEADSCREW ERROR COMPENSATION
AND STORED STROKE LIMITt
...............................
6 ........ 6.4 ....... 214
PREPARATION FOR TURNING OFF POWER .......................6 ........ 6.10 .“...- 217
PREPARATIONS FOR AUTOMATIC OPERATION
6
..................... ........
6.5 ......-. 214
PREPARATORY FUNCTIONS (G-FUNCTION) ........................ 2 .......” 2.8 -------- 23
PROCESS SHEET ...........................”.. ..,.......-.””-”-””3 ““-””--” 3.2.1”””-”- 148
PRoGRAMh41NG
.................................................... .....................
2
1
PROGRAMMING
....................................................
3 ........ 3.2 ‘.....- 148
PROGRAhIMING OF ABSOLUTE ZERO POINT (G50)
.................
2
........
2.8.20
.-”-4 61
PROGRAM MIRROR IhiAGE (G68, G69)t
............................
2
........
2.8.24 .... 92
PROGRAM NUMBER
................................................
2
........
2.2,1
.....
6
PROGRAM NUMBER AND SEQUENCE NUMBER
......................
2
........
2.2
6
PROGRAM RESTART SWITCHt ..................................... 5
.......
........
5.1.26 .... 195
PROGRAM RESTARTt .......-..........~.......................... 5 ....---- 5.2.6 ““”-- 209
Program Return
................................................... ........
4 4.3.4.5
... 164
PUSHBUTTONS, KEYS, AND LAMPS
...............................
4
...$.... 4,1
.......
151
R
RADIUS PROGRAMMING FOR CIRCULAR INTERPOLATION
(G22, G23)t .................................""-""""----"""-""2 ““””””””2.8.9 ”-””-- 33
RAPID TRAVERSE RATE
...........................................
2 .....s.. 2.4
.......
10
RAPID TRAVERSE RATE.... ....................................... 2 ...~....2.4.1
.....
10
RAPID TRAVERSE RATE OVERRIDE SWITCH
.......................
5 ........ 5.1.11 .... 192
REFERENCE POINT CHECK (G27)
..................................
2 ........ 2.8.10 -... 34
REFERENCE POINT LAMPS
..............................
..........
5 ........ 5,1.15 .... 193
Registrationof Macro Programs .................................... 2 ........ 2.8.23.7... 83
RESET KEY ..........................................-.....O------4 .-o-----4.1.12 ..-.. 155
RETURN FROM REFERENCE pOINT (G29)
..........................
2 ........ 2.8.12
.....
36
v
To Next Page
Loading...
Need help?
General
