GET TO KNOW THE REMOTE CONTROL: MBR3447
PROGRAMMING YOUR REMOTE
If you are using Zenith products, the remote is programmed for the most commonly used codes. For other audio/video brands you
will have to program the remote.
Follow these steps for each product you are using:
To program the remote
1. Locate the three-digit code for your brand (such as Zenith) and
equipment (such as VCR) in the code table.
2. Press and hold PRG with a small blunt object until the indicator
lights (about three seconds).
3. Press TV, VCR, CABLE or AUX to select the product you
want your remote to control. (Use CABLE or AUX to
program your remote for a second TV or VCR or to
program your remote for a video disc player or audio
equipment.)
4. Enter the three-digit code then press ENTER. The indicator light
should flash then turn offto indicate that the code was accepted. If
the light stays on, repeat steps 3 and 4 or lay using a different code.
5. Write the codes that operate your equipment on the label
inside the battery compartment for future reference.
NOTES:
FI To erase all code programming and return to the factory
preset code,;, enter code 9--1--1 when progr;anming the
remote.
C__lIf no key on your remote is l:,ressed within 60 seconds, the
programming process will stop, and you will have to start
again.
O You may cancel programrning at any time by pressing PRG.
SPECIAL FEATURES
AUX+I, AUX+2, AUX+3 CAPABILITY
Your remote can control up to seven electronic components. If
you have programmed the remote for four components using the
'rv, VCR, CABLE and AUX keys, you may also program it for
ap to three additional components.
To program AUX+I, AUX+2, & AUX+3
1. Locate _he..three-digit code for your equipment in the code table.
2. Press and hold PRG until the indicator lights.
3. Press AUX and "1" simultaneously to select AUX+I.
4. Enter the three-digit code then press ENTER. The indicator light
should tlash then turn off to indicate that the code was accepted. If
the light stays on, repeat steps 3 and 4 or try using a different code.
5. Repeat steps 2 --4 for AUX+2 and AUX+3 programming.
6. Write the codes that operate your equipment on the label
inside the battery compartment for future reference.
Once programmed, hold down the AUX key and press 1, 2 or 3,
to access the °oBditional AUX +1, 2 or 3 mode.
CABLE BOX VOLUME
You may use your remote to control cable box volume and
muting if available on your equipment.
To program the cable box volume
Program your cable box code into the CABLE or the AUX mode.
Repeat the programming steps, again using the CABLE or AUX
key, but key-in code 3-9-9 instead of a brand code and press
ENTER.
NOTE:
[] To restore TV volume/mute control to the CABLE or AUX
mode, reprogram your cable code into that mode.
AMPLIFIER VOLUME OVERRIDE
You may use your remote to override your TV, VCR or video
disk player's volume functions wlth your amplifier's "volume and
muting.
To program the amplifier volume override
1. Program your amplifier code into the CABLE or one of the
AUX modes.
2. Select the mode on your remote (TV, VCR, etc.) where you
want the amplifier volume control function to appe_m In other
words, if you want to operate the volume and mute of your
amplifier while the remote is in TV mode, press TV for this step.
3. Enter code 4-9-9, followed by ENTER.
The amplifier volume and mute fi_atures are now available in the
TV mode.
NOTES:
[] To restore normal volume: and muting cont:Fol to your TV
cable box, reprogram the remote for these units into each
mode (TV, VCR, etc.) to be restored.
[] CD and tape devices will automatically select amplifier
volume and mute.
3048-o 3 -- 4
To Next Page
Loading...
