To Next PageTo Next PageHow to fix Zenith DVD VCR Combo when there is no power?
If your Zenith DVD VCR Combo has no power, the power cord might be disconnected. Make sure to securely plug the power cord into the wall outlet.
Why is my Zenith XBV243 remote control not working?
If the remote control for your Zenith DVD VCR Combo isn't working correctly, consider the following: * Ensure you're pointing the remote at the DVD+VCR's remote sensor. * Make sure you're within 23 ft (7 m) of the DVD+VCR. * Remove any obstacles between the remote and the DVD+VCR. * Replace the batteries in the remote with new ones. * If using the VCR, press the VHS button first; for DVD, press the DVD button first.
How to fix Zenith XBV243 with no power?
If your Zenith DVD VCR Combo has no power, the power cord might be disconnected. Ensure the power cord is securely plugged into the wall outlet.
Why is my Zenith DVD VCR Combo remote not working?
If the remote control for your Zenith DVD VCR Combo isn't working correctly, try these steps: 1. Point the remote control directly at the remote sensor on the DVD+VCR. 2. Ensure you are within 23 ft (7 m) of the DVD+VCR. 3. Remove any obstacles between the remote and the DVD+VCR. 4. Replace the batteries in the remote with new ones. 5. If using the VCR, press the VHS button first. If using a DVD, press the DVD button first.
What to do if picture and sound are weak on Zenith DVD VCR Combo?
If the picture and sound of a broadcasting channel are weak or missing on your Zenith DVD VCR Combo, try these steps: * Tighten any loose antenna or cable connections, or replace the cable. * Try all CHANNEL SOURCE options.
Why is timer recording not possible on my Zenith DVD VCR Combo?
If timer recording isn't working on your Zenith DVD VCR Combo, check the following: * Ensure the clock in the DVD+VCR is set to the correct time. * Make sure the DVD+VCR is turned off to enable the timer (the TIMER indicator light should appear). * Reprogram the Timer if it has been programmed incorrectly. * If the TIMER indicator light doesn't appear, reprogram the timer and turn the DVD+VCR off. * Note that if the DVD+VCR is in Timer Recording mode, this is the normal indication.
How to improve poor playback picture on Zenith XBV243 DVD VCR Combo?
If the playback picture quality is poor on your Zenith DVD VCR Combo, consider these solutions: * Clean the disc. * Clean the video heads. * If using a rental tape or one recorded on another VCR, use CH/TRK (v/V) for manual tracking adjustment while the tape is playing.
What to do if the camcorder image is not shown on Zenith VCR?
If the camcorder image is not showing on your Zenith VCR, ensure the camcorder is turned on and operating properly. Also, verify that the VCR SOURCE is set to AUX by pressing INPUT to select the LINE input channel.
Why is timer recording not possible on my Zenith VCR?
If timer recording isn't working on your Zenith VCR, ensure the clock is set to the correct time. Make sure the VCR is turned off to enable the timer. If the timer has been programmed incorrectly, reprogram it. Note that if the VCR is in Timer Recording mode, this is normal.
Why are the picture and sound weak on my Zenith VCR?
If the picture and sound of a broadcasting channel are weak or missing on your Zenith VCR, tighten the antenna or cable connections or replace the cable. Try all CHANNEL SOURCE options.
General| Type | DVD VCR Combo |
|---|---|
| Video Format | NTSC |
| Recording Formats | VHS |
| Remote Control | Yes |
| Playback Formats | DVD, VHS |
| Connections | Composite video output |
