Zephyr Cyclone AK6500CS

Questions and Answers

D
Dorothy GonzalezAug 18, 2025
What to do if my Zephyr Cyclone AK6500CS doesn't work after installation?
- T
  Todd SolisAug 19, 2025
  If your Zephyr Ventilation Hood doesn't work after installation, check the following: Ensure the power source is turned ON by verifying the circuit breaker and unit's power are ON. Check that the power line and cable locking connector are properly connected to the unit. Make sure the wirings at the switch board and control board are connected correctly. If the switch board or control board is defective, it should be replaced.
C
Christy SloanAug 21, 2025
Why does my Zephyr Cyclone AK6500CS Ventilation Hood turn on by itself?
- K
  Kendra OrrAug 21, 2025
  If your Zephyr Ventilation Hood turns on by itself, it might be because a spotlight or kitchen lamp is shining directly onto the switch controls. The switch controls are light sensitive, and a direct light source can disrupt their function.
K
Kendra RiveraAug 23, 2025
What to do if my Zephyr Cyclone AK6500CS turns on by itself?
- E
  Eric NguyenAug 25, 2025
  If your Zephyr Ventilation Hood turns on by itself, it might be because a spotlight or kitchen lamp is shining directly onto the switch controls. These controls are light sensitive, and a direct light source may disrupt their function.
B
Brian AustinAug 26, 2025
What to do if Zephyr Ventilation Hood light works, but the blower isn't turning?
- M
  Michael ClarkAug 26, 2025
  If the light works but the blower isn't turning on your Zephyr Ventilation Hood, there could be several reasons: * The blower cable might be disconnected, so check and connect it. * There might be debris or an obstruction in the motor, which you should remove. * The motor could be defective or seized, requiring you to change the blower. * A damaged capacitor could also be the cause, so replace the capacitor. * Lastly, the switch board or control board might be defective, requiring you to change the defective part.
B
Belinda JenkinsAug 28, 2025
How to fix lights if the blower is working on Zephyr Cyclone AK6500CS Ventilation Hood?
- J
  James ChambersAug 28, 2025
  If the blower is working, but the lights are not on your Zephyr Ventilation Hood, check these potential issues. First, the LED light connector might be disconnected; ensure it is properly connected. Second, the LED light itself could be defective and need replacement. Finally, the switch board or control board might be defective, and you would need to change it.
C
cfloresAug 30, 2025
What to do if my Zephyr Ventilation Hood light works but the blower isn't turning?
- N
  Nicole HaynesAug 30, 2025
  If the light works, but the blower isn't turning on your Zephyr Ventilation Hood, several issues could be the reason. Start by checking the blower cable to ensure it's properly connected. Also, inspect the motor for any debris or obstructions that may be preventing it from turning. If those aren't the problem, the motor may be defective or seized, the capacitor might be damaged, or the switch board or control board could be defective, requiring you to change the defective part.
V
Vanessa AvilaSep 1, 2025
What to do if my Zephyr Cyclone AK6500CS Ventilation Hood is vibrating?
- L
  Laura JensenSep 1, 2025
  If your Zephyr Ventilation Hood is vibrating, it could be due to several reasons. First, check if the blower is securely in place and tighten it if necessary. A damaged blower wheel can also cause vibration, so consider replacing it. Lastly, ensure the hood itself is properly secured; check the installation.
C
Christine ThomasSep 4, 2025
What to do if my Zephyr Ventilation Hood doesn’t work after installation?
- M
  mike85Sep 4, 2025
  If your Zephyr Ventilation Hood doesn’t work after installation, first ensure that the power source is turned ON by checking the circuit breaker and the unit's power. Then, verify that the power line and cable locking connector are properly connected. Also, check the wirings at the switch board and control board to ensure they are connected correctly. If the problem persists, the switch board or control board may be defective and need to be replaced.
M
Meghan Frey DVMSep 6, 2025
Why is my Zephyr Ventilation Hood not venting properly?
- D
  Derrick CowanSep 6, 2025
  There are several reasons why your Zephyr Ventilation Hood might not be venting properly. It could be due to using the wrong type of ducting; flexible ducting can reduce airflow by up to 50%, so change to solid rigid metal ducting. The hood might be hanging too high from the cooktop; adjust the distance to be within 24” and 32”. Also, wind from opened windows or doors can affect ventilation, so close them. Finally, there might be a blockage in the duct opening or ductwork; remove any obstructions.
L
lmayerSep 8, 2025
Why is my Zephyr Cyclone AK6500CS vibrating?
- L
  Lisa VanceSep 9, 2025
  If your Zephyr Ventilation Hood is vibrating, it could be due to a few reasons. The blower might not be secured in place, so tighten it. A damaged blower wheel could also cause vibration, requiring you to replace the blower. Lastly, the hood itself might not be secured properly, so check the installation.

Summary

Safety Information

General Safety

General safety guidelines and warnings for using the appliance.

Operation

Electrical Requirements

Guidelines for proper electrical installation and connections.

Installation Instructions

Mounting Height, Clearance, & Ducting

Specifies recommended height, clearance, and ducting requirements.

Ducting Options

Electrical Supply

Information on the required electrical supply and safety precautions.

Mounting the Hood

Step-by-step guide for physically mounting the hood to the cabinet.

Features & Controls

AK21 Capacitive Touch

AK25 Electronic Touch

AK65 Mechanical Slide

Maintenance

ACT Conversion

Airflow Control Technology (ACT)

Explanation of Airflow Control Technology for CFM adjustment.

Enabling ACT

Steps to enable and configure the ACT™ feature.

Accessing PC Board Instructions

Wiring Diagram

Troubleshooting

Limited Warranty

Zephyr Cyclone AK6500CS Specifications

General

Color	stainless steel
Hood Type	under cabinet
Venting Type	ducted, external
Temperature Sensor	no
Number of Fan Speeds	3
CFM	600 cubic feet per minute
Sones	5 sones
Control Type	slide
Delay Start	no
Interior Light	yes
Remote Control	no
Voltage	120 volts