3M Attest Auto-reader 490H - Repair and Replacement

8 9
1
Code/ Issue Problem Solution
Other
Negative Control Vial
Control vial was sterilized.
Check process indicator on BI cap. Use a non‑sterilized vial as a control.
Other
Unexplained PositiveBI
Adhesive residue on vial.
Do not place tape or labels on vial.
Other
Unexplained PositiveBI
Test vial is absorbing fluorescent residue from a chemical indicator or tape.
Place the vial so it does not come in direct contact with chemical indicators
or tape.
Other
3M™ Attest™ Auto‑reader 490H will not enter Configurationmode.
Pushbutton Configuration may be disabled on 3M™ Attest™ Auto‑reader 490H
Web App.
On 3M™ Attest™ Auto‑reader 490H Web App Configuration Page, go to
Pushbutton Configuration and select the Enable radio button. Save changes to
begin using new setting.
Other
3M™ Attest™ Auto‑reader 490H LCD display flashes and asterisks (***) and/or
E11and/or C4codes appear on display below unoccupied incubation wells.
Move 3M™ Attest™ Auto‑reader 490H away from sunlight or sources of
incandescent light.
OPTIONAL 3M™ ATTEST™ AUTO‑READER 490H WEB APP
Web BrowserRequirements
The web interface is designed to be viewed in Internet Explorer 8.0 or higher. Earlier
versions of Internet Explorer or other browsers may result in some web pages being
displayed in a less-than-optimal manner. For best results, switching to Internet Explorer
8.0 or higher is recommended. For full functionality, the use of an HTML5 compliant
browser with JavaScript enabled is required.
EthernetConnection:
Connection switch/router with auto‑negotiation capability to identify the Auto‑reader as
operating at 10Mbps and half‑duplex, or able to be manually configured as 10Mbps
andhalf‑duplex.
Connecting to the 3M™ Attest™ Auto‑reader 490H Web App
To use the 3M™ Attest™ Auto-reader 490H Web App, the 3M™ Attest™ Auto-reader
490H must be connected to the facility network using the supplied Ethernet cable. Consult
with your facility IT personnel for assistance with network connectivity. Each 3M™
Attest™ Auto-reader 490H has a unique MAC Address which is presented on the unit’s
LCD display when the user depresses the Info button three times. The MAC Address is also
provided at the bottom of the 3M™ Attest™ Auto-reader 490H Web App Configuration
page. Communication occurs using the http protocol over Port 80. The 3M™ Attest™
Auto-reader 490H does not collect, process, store, or transmit any Protected Health
Information (PHI). Web App Users may connect to the 3M™ Attest™ Auto-reader 490H
Web App using a URL based upon either the 3M™ Attest™ Auto-reader 490H serial
number or the IP Address. To view the 3M™ Attest™ Auto-reader 490H Web App from a
wireless device such as a mobile hand-held device or a computer on a sub-net different
from that to which the 3M™ Attest™ Auto-reader 490H is connected, use the IP Address
URL.
Note: To access the 3M™ Attest™ Auto‑reader 490H Web App within a secure network,
the PC or mobile device must have access to the secure network; options include
connecting via a network Ethernet cable, signing in to the facility’s wireless network, or
connecting via a virtual private network(VPN).
A. Serial numberURL
1. Connect the supplied Ethernet cable from the 3M™ Attest™ Auto‑reader 490H to an
Ethernetjack.
2. Depress the
button once to display the 3M™ Attest™ Auto‑reader 490H 6‑digit
serial number on the left side of the top row of text on the LCDdisplay.
3. Enter http://attestxxxxxx, where xxxxxx represents the unit’s serial number (e.g., http://
attest221008) from Step 2, in the PC web browser address bar and pressEnter.
4. The 3M™ Attest™ Auto‑reader 490H Web App Status page will display on the PC. For
future ease of use, add this page to your web browser “Favorites.”
B. IP AddressURL
The 3M™ Attest™ Auto‑reader 490H Web App may also be accessed using either a
dynamic or static IPaddress.
1. Dynamic IP Address
A dynamic IP address is assigned when the Ethernet cable is connected from the
3M™ Attest™ Auto‑reader 490H to a live Ethernetjack.
Press and release the
button twice to display the dynamic IP address for the
3M™ Attest™ Auto‑reader 490H. Enter http://IPaddress (e.g. http://123.456.789.012) in
the web browser address bar of the PC or mobile hand‑held device and press Enter. The
3M™ Attest™ Auto‑reader 490H Web App Status page willdisplay.
2. Static IPaddress
Some facility IT personnel may require devices connecting to the network to use a Static
IP address. If this is the case at your facility, contact the IT department to request a Static
IPaddress.
Record the static IP address provided by your facility IT department here:___________.
You may wish to label the Ethernet jack with the assigned address. Enter
http://StaticIPaddress (e.g. http://111.222.333.444) in the web browser address bar on
your PC or mobile hand‑held device and press Enter. The 3M™ Attest™ Auto‑reader 490H
Web App Status page willdisplay.
About the 3M™ Attest™ Auto‑reader 490H Web AppPages
The 3M™ Attest™ Auto‑reader 490H Web App includes fourpages.
a) Statuspage
Status
History
3M™ Attest™ Auto-reader 490H
AT TEST 1295 AT TEST 1295
Auto-reader 490H
1 2 3 4 5
+24–
678910
SN
200299
2017- 0 5 -11 17:13
1. User‑entered nickname(optional)
2. Well Configuration (1‑5and6‑10)
3. WellNumber
4. BI Result/Remaining Incubation Time
5. Date and Time
6. 3M™ Attest™ Auto‑reader 490H SerialNumber
The Status page provides a real‑time representation of the 3M™ Attest™ Auto‑reader
490H LCD panel display. The current date and time and 3M™ Attest™ Auto‑reader 490H
serial number are also indicated on this page. From this page, the user may navigateto:
• the History page by clicking on History on the left of thescreen.
• the Results Detail page by clicking on the well number of an occupied well (i.e., a well
that currently has an incubating BI). Clicking on an unoccupied well takes the user to
the Historypage.