To Next PageTo Next PageWhy can't I open the Results Detail page from the Status page on my 3M Laboratory Equipment?
The Results Detail page can only be opened from the Status page for occupied wells on your 3M Laboratory Equipment. Do not attempt to navigate to the Results Detail page from unoccupied wells on the Status page.
What should I do if I get an LED error on my 3M Laboratory Equipment?
If you receive an LED error on your 3M Laboratory Equipment, unplug the unit and plug it back in to attempt to clear the error. If the error continues, it means that the affected incubation well should not be used, and the unit may require repair or replacement.
What to do if a memory error occurs on 3M Laboratory Equipment?
If your 3M Laboratory Equipment displays a memory error, try unplugging the unit and then plugging it back in. If the error persists, this indicates that the unit may need to be repaired or replaced.
What to do if a communications error occurs on 3M Laboratory Equipment?
If a communications error occurs with your 3M Laboratory Equipment, unplug the unit and plug it back in to attempt to clear the error. If the error continues after restarting, the unit likely requires repair or replacement.
What to do if the LCD display on my 3M Laboratory Equipment is not working properly?
If the LCD display on your 3M Laboratory Equipment is not displaying correctly, first, unplug the unit and then plug it back in. If the display issue continues, it suggests the unit needs repair or replacement.
Why might I get an unexplained positive BI result on my 3M Laboratory Equipment due to adhesive residue?
If you observe an unexplained positive BI and notice adhesive residue on the vial, avoid placing tape or labels directly on the vial.
What if the negative control vial BI on my 3M Laboratory Equipment was not properly activated?
If the negative control vial BI was not properly activated, ensure the BI cap is closed and the glass ampoule is crushed. Flick the BI until the media flows to the spore chamber at the bottom of the BI.
What if the negative control vial on my 3M Laboratory Equipment was sterilized?
If the control vial was sterilized, check the process indicator on the BI cap. Make sure to use a non-sterilized vial as a control.
How to disable the alarm on 3M Laboratory Equipment?
If you are experiencing unwanted alarm sounds when a positive BI is detected on your 3M Laboratory Equipment, you can disable the alarm. Refer to the 3M Auto-reader Configuration section for instructions on how to do this.
Why is my 3M Laboratory Equipment alarming because of premature BI removal?
If the alarm sounds because the 3M Rapid Readout Biological Indicator was prematurely removed from the incubation/reader well, replace the indicator in the well within 10 seconds to prevent data loss.
General| Model | 490H |
|---|---|
| Manufacturer | 3M |
| Display | LCD |
| Power Supply | AC adapter |
| Connectivity | USB |
| Read Time | 24 minutes |
| Power Requirements | 100-240V AC, 50/60 Hz |
| Operating Temperature | 15°C to 30°C |
| Storage Temperature | -20°C to 60°C |
| Type | Automated Biological Indicator Reader |
| Weight | 2.3 kg |
| Compatibility | 3M Attest Biological Indicators |
| Incubation Temperature | 60°C ± 2°C |
| Relative Humidity | 20% to 80% (non-condensing) |
Disclaimers regarding sample printouts, graphics, displays, and screens for informational purposes only.
Disclaimer stating that hardware specifications are subject to change and may not match installed systems.
Defines the meaning of Warning and Caution symbols used in the manual.
Lists essential warnings and precautions to avoid unsafe actions and potential hazards.
Details the standards the Auto-reader 490H complies with, including IEC and UL standards.
Outlines the electromagnetic compatibility standards the device adheres to.
Details electrical specifications for the device's power supply.
Specifies the required environmental conditions for operation and storage.
Guidance on selecting a suitable location for the Auto-reader 490H.
Instructions for selecting and installing the appropriate power plug.
Procedure to wait for the device to warm up after plugging it in.
Recommendations regarding unit operation and power status.
Description of the ten incubation wells on the Auto-reader 490H.
Identification and function of the buttons on the Auto-reader 490H.
Explanation of the LCD display elements and indicators.
Details about the color-coded sticker for well configuration.
Procedure for setting the date and time on the Auto-reader 490H.
Instructions on how to enable or disable the audible alarm.
Screen for accepting or retaining configuration changes.
Steps for activating and incubating biological indicators.
Guidance on proper placement of biological indicators in the reader wells.
Procedure for using a positive control biological indicator daily.
How to interpret fluorescent results displayed on the LCD panel.
Information on obtaining a visual pH color change result for further incubation.
Description of the audible alarm for positive results and removed BI.
Procedure for silencing specific audible alarms and their limitations.
Information on stacking units to save counter space.
Details on how to access serial number, software version, date, time, and IP address.
Explanation of the Auto-reader's internal temperature self-diagnostic program.
Overview of configuration options via unit buttons or Web App.
Introduction to connecting the Auto-reader to a PC for additional capabilities.
Details on viewing individual records for incubated Biological Indicators.
Summary of the last 100 incubated Bls stored on the Auto-reader.
Information on configuring network and language settings via the Web App.
Setting the display language for the Web App.
Enabling or disabling unit configuration via the device buttons.
Enabling or disabling the audible alarm feature.
Assigning a nickname for easier identification of multiple units.
Option to use dynamic IP addresses automatically assigned by the network.
Field to enter a static IP address if required by facility IT.
Field to enter the network gateway address.
Field to enter the network subnet mask.
Field to enter the primary DNS server address.
Field to enter the secondary DNS server address.
Displays the device's unique Media Access Control address.
Option to synchronize the Auto-reader clock with the computer's clock.
Manual setting for the Auto-reader's clock if computer time is not used.
