ABB ACS510-01 - Page 57

ACS510 User’s Manual 57
Start-Up
Group 22: Accel/Decel
2201
ACC/DEC 1/2 SEL -6…7 1 5
2202 ACCELER TIME 1 0.0…1800.0 s 0.1 s 5.0 s
2203
DECELER TIME 1 0.0…1800.0 s 0.1 s 5.0 s
2204
RAMP SHAPE 10=LINEAR; 0.1...1000.0 s 0.1 s 0.0 s
2205 ACCELER TIME 2 0.0…1800.0 s 0.1 s 60.0 s
2206
DECELER TIME 2 0.0…1800.0 s 0.1 s 60.0 s
2207 RAMP SHAPE 20=LINEAR; 0.1...1000.0 s 0.1 s 0.0 s
2208
EM DEC TIME 0.0…1800.0 s 0.1 s 1.0 s
2209
RAMP INPUT 0-6…7 1 0
Group 25: Critical Speeds
2501
CRIT SPEED SEL 0=OFF, 1 = ON 10
2502
CRIT SPEED 1 LO 0.0…500.0 Hz /
+N688:0.0...50.0 Hz /
+N689:0.0...55.0 Hz
0.1 Hz 0.0 Hz
2503
CRIT SPEED 1 HI 0.0…500.0 Hz /
+N688:0.0...50.0 Hz /
+N689:0.0...55.0 Hz
0.1 Hz 0.0 Hz
2504
CRIT SPEED 2 LO 0.0…500.0 Hz /
+N688:0.0...50.0 Hz /
+N689:0.0...55.0 Hz
0.1 Hz 0.0 Hz
2505
CRIT SPEED 2 HI 0.0…500.0 Hz /
+N688:0.0...50.0 Hz /
+N689:0.0...55.0 Hz
0.1 Hz 0.0 Hz
2506
CRIT SPEED 3 LO 0.0…500.0 Hz /
+N688:0.0...50.0 Hz /
+N689:0.0...55.0 Hz
0.1 Hz 0.0 Hz
2507
CRIT SPEED 3 HI 0.0…500.0 Hz /
+N688:0.0...50.0 Hz /
+N689:0.0...55.0 Hz
0.1 Hz 0.0 Hz
Group 26: Motor Control
2601 FLUX OPT ENABLE 0 = OFF, 1 = ON 10
2602
FLUX BRAKING 0 = OFF, 1 = ON 10
2603
IR COMP VOLT 0.0 …100.0 V 0.1 V Size dependent
2604
IR COMP FREQ 0…100% 1% 80%
2605
U/F RATIO 1 = LINEAR, 2 = SQUARED, 3 = FREELY
DEFINED
12
2606
SWITCHING FREQ 1, 4, 8, 12 kHz - 4 kHz
2607
SW FREQ CTRL 0 = OFF, 1 = ON 11
2608
SLIP COMP RATIO 0…200% 1% 0
2609
NOISE SMOOTHING 0 = DISABLE, 1 = ENABLE 10
2610
USER U1
0...480 V 1 V 76 V
2611
USER F1
0.0…500.0 Hz /
+N688:0.0...50.0 Hz /
+N689:0.0...55.0 Hz
0.1 Hz 10.0 Hz /
+N688:10.0 Hz /
+N689:11.0 Hz
2612
USER U2
0...480 V 1 V 152 V
Code Name Range Resolution Default User S
Supplied from China by: Guangzhou Tofee Electro Mechanical Equipment Co., Ltd
Email: info@tofee.com.cn