ABB Relion REF615R - Page 49

1MRS240173-IB B Section 5
4x Registers
REF615R 43
DPU2000R Modbus Point List Mitigation Manual
41156 Password
character 3 & 4
41156 In REF615R, it is mapped for the password
2 for the control structure 1.
41157 Spare 41157 In REF615R, this register is mapped to
control open or close the circuit breaker.
Please see the rows below.
41158 Change initiate
input mask
41158 In REF615R, it is mapped for the
confirmation register for the control structure
1.
41159:14 Control button 6
(C6)
41187:10 LD0.SPCGGIO3.SPCSO6.Oper.ctlVal Control button 6 (C6) set
41187:11 Control button 6 (C6) reset
41159:13 Toggle SCADA
Redi
N/A in REF615R.
41159:12 Reset energy
meters
41162:10 LD0.SPEMMTR1.SupDmdRs.Oper.ctlVal Reset energy meters single phase
41162:12 LD0.PEMMTR1.SupDmdRs.Oper.ctlVal Reset energy meters in 3 phase
41159:11 Reset relay
status
N/A. In REF615R, status automatically
resets for the Modbus client who reads the
status register.
41159:10 Reset Min/Max
demands
41162:6 LD0.LLN0.MtrRecRs.Oper.ctlVal
41159:9 Reset Alarms 41162:8 LD0.LLN0.LEDRs1.Oper.ctlVal
41159:8 Reset LED
Targets
41162:9 LD0.LLN0.LEDRs2.Oper.ctlVal
41159:7 Control button 5
(C5)
41187:8 LD0.SPCGGIO3.SPCSO5.Oper.ctlVal Control button 5 (C5) set
41187:9 Control button 5 (C5) reset
41159:6 Control button 4
(C4)
41187:6 LD0.SPCGGIO3.SPCSO4.Oper.ctlVal Control button 4 (C4) set
41187:7 Control button 4 (C4) reset
41159:5 Close Initiate
(Independent of
43A)
41157:1 CTRL.CBCSWI1.Pos.Oper.ctlVal “Close” command in
SBO-with-enhanced-security mode. (Relay
needs to be set at Remote mode at first).
41157:2 “Cancel” command in
SBO-with-enhanced-security mode. Send
this command within 15 seconds delay after
sending the “Close” command to cancel the
“Close” command.
41157:3 “Select” command in
SBO-with-enhanced-security mode. Send
this command within 15 seconds delay after
sending the “Close” command to confirm the
“Close” command.
41157:5 “Close” command in
direct-with-normal-security mode. (Relay
needs to be set at Remote mode at first).
41159:4 Control button 3
(C3)
41187:4 LD0.SPCGGIO3.SPCSO3.Oper.ctlVal Control button 3 (C3) set
41187:5 Control button 3 (C3) reset
41159:3 Control button 2
(C2)
41187:2 LD0.SPCGGIO3.SPCSO2.Oper.ctlVal Control button 2 (C2) set
41187:3 Control button 2 (C2) reset
41159:2 Control button 1
(C1)
41187:0 LD0.SPCGGIO3.SPCSO1.Oper.ctlVal Control button 1 (C1) set
41187:1 Control button 1 (C1) reset
DPU2000R
register
addr.
DPU 2000R
description
REF615R
register
addr.
IEC 61850 path
Comments on REF615R Modbus points
mapping