To Next PageTo Next PageHow to deal with rubbing of rotating parts in ABB TPS48-F32?
If you notice rubbing of rotating parts in your ABB Industrial Equipment, contact an ABB Turbocharging Service Station if there is any doubt about the extent of the rubbing. Also, have a dimension check carried out by an ABB Turbocharging Service Station.
What to do if ABB TPS48-F32 has charge air pressure too low?
If the charge air pressure is too low, there could be several reasons. The air receiver or the gas piping between the engine and the turbine might be leaking. A poorly adjusted injection system also can cause this issue, so correct it. The manometer display might be providing a wrong reading, so replace the manometer, or the line to the manometer might be leaking, so repair the leak. A contaminated filter silencer causing excessive loss of pressure can also be the reason, so clean it. In some cases, the compressor/turbine might be damaged, which requires contacting an ABB Turbocharging Service Station. High exhaust counterpressure can also cause low charge air pressure, so clean or repair the boiler or exhaust silencer.
What causes fouling of the compressor in my ABB charger?
Fouling of the compressor in your ABB charger, due to the feeding in of ventilation gases, may result from: * Heavy fouling of the compressor components: Clean compressor. * Material of compressor wheel corroded: Check the fuel and its corrosive components, and change fuel if necessary.
Why is there fouling of the compressor due to the feeding in of ventilation gases in ABB Industrial Equipment?
Fouling of the compressor due to the feeding in of ventilation gases can occur due to heavy fouling of the compressor components, so clean compressor. It can also lead to increased vibrations or compressor blade damage, so correct the feed of ventilation gases according to instructions of enginebuilder. The material of the compressor wheel might be corroded, so check the fuel and its corrosive components, and change fuel if necessary.
What to do if ABB TPS48-F32 Industrial Equipment has charge air pressure too high?
If the charge air pressure is too high, it could be due to a malfunctioning or poorly adjusted injection system, so repair or correct it. The engine performance might also be higher than expected, so check engine performance. The manometer display might be providing a wrong reading, so replace the manometer.
What to do if the charge air pressure is too low in ABB TPS48-F32?
If your ABB Industrial Equipment experiences charge air pressure that is too low, several factors could be responsible. You can repair any leaks in the air receiver or correct a poorly adjusted injection system. Additionally, you should replace the manometer if the display is wrong, or repair the leak if the line to the manometer is leaking. Clean the filter silencer if it is contaminated, causing excessive pressure loss. Finally, clean or repair the boiler or exhaust silencer if the exhaust counterpressure is too high.
Why is my ABB TPS48-F32 Industrial Equipment having a sluggish start-up?
If your ABB Industrial Equipment experiences a sluggish start-up, it could be due to a few reasons. The turbocharger might be contaminated and need cleaning. Alternatively, there may be damage to the bearing, in which case you should contact an ABB Turbocharging Service Station. Other potential causes include a rubbing rotor or a foreign object present in the turbocharger.
What to do if my ABB charger is surging?
If your ABB turbocharger is surging, it could be due to: * A contaminated or damaged guard in front of the turbocharger: Clean or replace it. * A contaminated filter silencer or diffuser: Clean it. * A contaminated cooler: Clean it. * A blocked charge air duct.
Why is there a reduction in speed in my ABB charger?
A reduction in speed in your ABB charger can stem from: * Defects of connected cylinders when pulse charging: Contact the enginebuilder. * Heavy contamination of the turbine: Clean it. * Damaged rotor components or bearing: Contact an ABB Turbocharging Service Station. * Defects such as leaks in the exhaust gas pipes or charge air ducts: Make repairs.
Why is the charge air pressure too high in my ABB charger?
If the charge air pressure is too high in your ABB charger, it may be due to: * A malfunctioning injection system: Repair it or contact the manufacturer. * A poorly adjusted injection system: Correct it. * Engine performance higher than expected: Check engine performance. * Manometer display wrong: Replace the manometer.
General| Brand | ABB |
|---|---|
| Model | TPS48-F32 |
| Category | Industrial Equipment |
| Language | English |
Introduces safety aspects, residual risks, and operator responsibilities.
Outlines general safety for operation, work area, and specific tasks.
Details risks like mechanical hazards, noise, and hot surfaces.
Details requirements for lubrication, oil filtration, viscosity, and pressure.
Covers checks before and after commissioning and during operation.
Explains routine checks, visual inspections, and functional checks.
Details procedures for shutting down oil-cooled and water-cooled turbochargers.
Explains wet cleaning methods for the compressor stage.
Covers methods for cleaning turbine components to maintain efficiency.
Lists possible causes and solutions for sluggish start-up and vibrations.
Addresses causes of surging and potential component damage.
Covers issues like low oil pressure, speed changes, and temperature problems.
Step-by-step guide for disconnecting and removing the turbocharger.
Instructions for mounting the turbocharger, including torque values.
Detailed procedures for component removal and reassembly.
