To Next PageTo Next PageWhat to do if rotating parts of ABB TPS48-F32 Industrial Equipment are rubbing?
Rubbing of rotating parts in ABB Industrial Equipment can be normal behavior and not a malfunction. If there is any doubt about the extent of rubbing, then an ABB Turbocharging Service Station must be contacted.
What to do if ABB TPS48-F32 Industrial Equipment is vibrating?
If your ABB Industrial Equipment is vibrating, it may be due to rotor unbalance. In this situation, contact an ABB Turbocharging Service Station.
How to fix sluggish start-up of ABB TPS48-F32?
A sluggish start-up of your ABB Industrial Equipment can occur if the turbocharger is contaminated. In this case, clean the turbocharger. Another possible cause is a damaged bearing. If the bearing is damaged, contact an ABB Turbocharging Service Station.
How to deal with rubbing of rotating parts in ABB TPS48-F32?
If you notice rubbing of rotating parts in your ABB Industrial Equipment, contact an ABB Turbocharging Service Station if there is any doubt about the extent of the rubbing. Also, have a dimension check carried out by an ABB Turbocharging Service Station.
Why is my ABB TPS48-F32 Industrial Equipment vibrating?
Vibrations in your ABB Industrial Equipment can occur due to several reasons. It might be caused by rotor unbalance, in which case you should contact an ABB Turbocharging Service Station. Vibrations can also arise from a damaged turbine or compressor, or a damaged bearing.
Why is my ABB Industrial Equipment start-up sluggish?
A sluggish start-up of your ABB Industrial Equipment can be attributed to several factors. The turbocharger may be contaminated and needs cleaning. Alternatively, there could be a damaged bearing, in which case you should contact an ABB Turbocharging Service Station. Other possible causes include a rubbing rotor or a foreign object present in the turbocharger.
Why is there an increase in speed in my ABB charger?
An increase in speed in your ABB charger may be caused by: * A heavily contaminated nozzle ring (with 4-stroke application): Contact an ABB Turbocharging Service Station.
Why is my ABB charger vibrating?
If you're experiencing vibrations in your ABB charger, it might be due to: * Rotor unbalance: Contact an ABB Turbocharging Service Station.
How to fix a sluggish start-up on my ABB charger?
A sluggish start-up in your ABB charger can be caused by: * A contaminated turbocharger: Clean it. * A damaged bearing: Contact an ABB Turbocharging Service Station.
Why is the lubricating oil pressure too low in my ABB charger?
If the lubricating oil pressure is too low in your ABB charger, consider the following: * Oil filter heavily contaminated: Clean it. * Defective oil pump in lubricating system: Check or replace it. * Manometer display wrong: Replace the manometer. * Rotor axial clearance too large: Contact an ABB Turbocharging Service Station.
General| Brand | ABB |
|---|---|
| Model | TPS48-F32 |
| Category | Industrial Equipment |
| Language | English |
Introduces safety aspects, residual risks, and operator responsibilities.
Outlines general safety for operation, work area, and specific tasks.
Details risks like mechanical hazards, noise, and hot surfaces.
Details requirements for lubrication, oil filtration, viscosity, and pressure.
Covers checks before and after commissioning and during operation.
Explains routine checks, visual inspections, and functional checks.
Details procedures for shutting down oil-cooled and water-cooled turbochargers.
Explains wet cleaning methods for the compressor stage.
Covers methods for cleaning turbine components to maintain efficiency.
Lists possible causes and solutions for sluggish start-up and vibrations.
Addresses causes of surging and potential component damage.
Covers issues like low oil pressure, speed changes, and temperature problems.
Step-by-step guide for disconnecting and removing the turbocharger.
Instructions for mounting the turbocharger, including torque values.
Detailed procedures for component removal and reassembly.
