To Next PageTo Next PageWhat to do if my Abbott Measuring Instruments reader does not power on?
If your Abbott Measuring Instruments reader doesn't power on, it could be due to a low battery. Try charging the reader. Alternatively, the reader might be outside its operating temperature range. Move the reader to a temperature between 50 °F and 113 °F and then try to power it on.
What to do if I get Error Message E-1 on Abbott Measuring Instruments?
If you receive Error Message E-1 on your Abbott Measuring Instruments, follow these steps: 1. Move the reader and test strips to a location where the temperature is within the test strip operating range. 2. Wait for the reader and test strips to adjust to the new temperature. 3. Repeat the test using a new test strip.
Why Abbott FreeStyle Libre 2 reader does not power on?
The Abbott Blood Glucose Meter reader may not power on due to several reasons: the reader battery is too low (charge the reader), the reader is outside of its operating temperature range (move the reader to a temperature between 10 °C and 45 °C and then try to power it on).
What to do if Abbott FreeStyle Libre 2 shows 'Scan Timeout'?
If your Abbott Blood Glucose Meter displays a 'Scan Timeout' message, it means the reader isn't close enough to the sensor. To resolve this, hold the reader within 4 cm (1.5 inches) of the sensor.
What to do if Abbott FreeStyle Libre 2 displays 'Scan Error'?
If your Abbott Blood Glucose Meter displays a 'Scan Error' message, it means that the reader was unable to communicate with the sensor. To resolve this, try scanning again.
What to do if Abbott FreeStyle Libre 2 shows 'Sensor Error'?
If your Abbott Blood Glucose Meter displays a 'Sensor Error' message, it means that the system is unable to provide a glucose reading. To resolve this, scan again in 10 minutes.
What to do if Abbott FreeStyle Libre 2 Blood Glucose Meter says 'Replace Sensor'?
If your Abbott Blood Glucose Meter indicates 'Replace Sensor,' it means the system has detected a problem with your sensor. Apply and start a new sensor.
What to do if Abbott FreeStyle Libre 2 displays 'Blood Glucose or Ketone Error Messages'?
If your Abbott Blood Glucose Meter displays 'Blood Glucose or Ketone Error Messages,' it could be due to several reasons: the temperature is too hot or too cold for the reader to work correctly (move the reader and test strips to a location where the temperature is within the test strip operating range), your Sensor has ended (replace your Sensor with a new one), reader error (turn off the Reader).
What to do if Abbott Blood Glucose Meter displays 'Check Sensor'?
If your Abbott Blood Glucose Meter displays 'Check Sensor', it might be because the sensor tip may not be under your skin. Try to start your sensor again.
Why my Abbott FreeStyle Libre 2 reader does not power on?
If your Abbott Blood Glucose Meter reader does not power on, it could be due to a low battery. Try charging the reader. Alternatively, the reader might be outside of its operating temperature range. Move it to a location with a temperature between 10°C and 45°C and try powering it on again.
General| Sensor Life | 14 days |
|---|---|
| Communication | Bluetooth |
| Water Resistance | IP27 |
| Calibration | Factory calibrated |
| Manufacturer | Abbott |
| Model | FreeStyle Libre 2 |
| Sensor Type | Flash glucose monitoring |
| Requires Finger Prick | No |
| Warm-up Time | 1 hour |
| Operating Temperature | 10°C to 45°C (50°F to 113°F) |
| Meter Category | Continuous Glucose Monitoring (CGM) |
| Accuracy | MARD 9.2% |
| Storage Temperature | -20°C to 60°C (-4°F to 140°F) |
| Compatibility | FreeStyle LibreLink app |
| Measurement Range | 20 to 500 mg/dL |
| Data Storage | 8 hours |
