Home
Agilent Technologies
Test Equipment
54810A
Agilent Technologies 54810A User Manual
4
of 1
of 1 rating
132 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
Setting U
p the Oscill
oscope
To attac
h
the opt
ional tra
ckball
1-1
3
2
While holdi
ng the latch in, sl
ide the metal tab
s down and t
o the fr
ont of
the
oscil
losco
pe
unt
il the
y
touc
h the
en
ds o
f th
e s
lot.
Fig
ure 1
-6
Sli
de the Meta
l Tabs
16
18
Table of Contents
Table of Contents
3
Setting up the Oscilloscope
5
To Inspect Package Contents
7
To Inspect Options and Accessories
9
To Connect Power
12
To Connect the Mouse or Other Pointing Device
15
To Attach the Optional Trackball
16
To Connect the Keyboard
21
To Connect to the LAN Card
22
To Connect Oscilloscope Probes
23
To Connect a Printer
26
To Connect an External Monitor
28
To Connect an GPIB Cable
29
To Tilt the Oscilloscope Upward for Easier Viewing
30
To Turn on the Oscilloscope
32
To Turn off the Oscilloscope
33
To Verify Basic Oscilloscope Operation
34
To Clean the Oscilloscope
36
Working in Comfort
37
About Repetitive Strain Injury
39
Mice and Other Input Devices
40
Using the Oscilloscope
41
To Set the Oscilloscope to a Known Starting Condition
47
To Start and Stop Waveform Acquisition
48
To Clear the Waveform Display
49
To Turn a Channel on or off
50
To Change Input Impedance and Input Coupling
51
To Adjust Vertical Scale and Offset
52
To Adjust Sweep Speed and Horizontal Position
53
To Magnify a Part of the Waveform Using Delayed Sweep
54
To Set the Oscilloscope to Trigger on an Edge
55
To Use the Markers
56
To Use the Quick Measurements
57
To Reinitialize the Oscilloscope
58
To Switch between the Graphical Interface and Full-Screen Mode
70
To Perform Basic User Interface Operations
71
To Select a Command from the Menu Bar
73
To Select a Command from a Context-Sensitive Menu
74
To Change the Mouse Settings
76
To Start and Stop Waveform Acquisition
77
To Clear the Waveform Display
78
To Print the Screen
79
To Turn a Channel on or off
80
To Adjust the Vertical Offset
81
To Adjust Vertical Scaling
83
To Access the Channel Setup
84
To Set the Horizontal Reference Point
85
To Adjust Sweep Speed
86
To Adjust Horizontal Position
87
To Access the Horizontal Setup
88
To Zoom on a Section of the Waveform
89
To Move the Markers Using the Graphical Interface
91
To Make a Measurement on a Waveform
92
To Access the Trigger Setup
94
To Set an Edge Trigger
95
To Enable 8.0 Gsa/S Sampling Mode on the 54845A
96
To Enable 4.0 Gsa/S Sampling Mode on the 54835A
97
To Set Dialog Box Preferences
98
To Install the Printer Software
101
To Set up the Network
109
To Recover Your Infiniium Hard Disk
110
Using the Built-In Information System
111
To Access the Information System
114
To Select the Built-In Information System Language
120
To Navigate through the Information System
121
To Access Context-Sensitive Information
122
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Agilent Technologies 54810A and is the answer not in the manual?
Ask a question
Agilent Technologies 54810A Specifications
General
Brand
Agilent Technologies
Model
54810A
Category
Test Equipment
Language
English
Related product manuals
Agilent Technologies 54835A
208 pages
Agilent Technologies 54831A
133 pages
Agilent Technologies 54853A
194 pages
54830 Series
133 pages
Agilent Technologies 54621A
276 pages
Agilent Technologies 54624A
276 pages
Agilent Technologies 54622D
276 pages
Agilent Technologies 54641A
276 pages
Agilent Technologies 54622A
276 pages
Agilent Technologies 5530
378 pages
Agilent Technologies 5000 Series
126 pages
InfiniiVision 5000 Series
428 pages
Need help?
General
To Next Page