Agilent Technologies E8362C User Manual

Index
Service Guide E8364-90026 Index-13
part numbers, 6-78
in internal analyzer
illustrated
, 6-73
part numbers
, 6-72
in rear panel assembly
illustrated
, 6-77
part numbers
, 6-76
in top assembly, Option 080
illustrated
, 6-17
part numbers
, 6-16
in top assembly, without
Option 080
illustrated
, 6-13
part numbers
, 6-12
locating
by reference designator
, 6-6
by type of part
, 6-8
miscellaneous
part numbers
, 6-80
replaceable
listing of
, 6-6
ordering information
, 6-3
parts, hardware
in bottom assembly
illustrated, 6-69, 6-71
part numbers
, 6-68, 6-70
password
Agilent administrator, 7-66
performance
tests, 3-31
calibration coefficients
, 3-36
description of
, 3-7
dynamic accuracy, 3-38
frequency accuracy
, 3-33
noise floor
, 3-35
receiver compression, 3-34
source maximum power
output
, 3-32
source power accuracy
, 3-31
source power linearity
, 3-32
system crosstalk
, 3-37
test port crosstalk
, 3-37
test port output maximum
power
, 3-32
test port output power
accuracy
, 3-31
test port output power
linearity
, 3-32
trace noise
, 3-33
verification
ANSI/NCSL Z540-1-1994
, 3-9
non-ANSI/NCSL Z540-1-1994
,
3-10
phase lock
IF gain adjustment, 3-48
phase lock board
illustrated, 6-13, 6-17
operation
, 5-10
part number
, 6-12, 6-16
removal and replacement
illustrated
, 7-21
procedure
, 7-20
test nodes
, 4-37
phase stability check
failure of, 3-17
test port cables
, 3-16
pin assignments
connectors
AUX I/O, 5-15
HANDLER I/O
, 5-14
TEST SET I/O
, 5-13
ping
command, LAN, 4-25
from network
, 4-26
to analyzer
, 4-25
pixel
damaged, 4-19
definition
, 4-19
PMYO (permanent-magnet YIG
oscillator)
frequency adjustment, 3-42
theory of operation, 5-10
Port 1
attenuator
removal and replacement
,
7-56
check
, 3-11
typical power output
, 4-48
Port 2
attenuator
removal and replacement
,
7-56
check, 3-11
typical power output
, 4-49
post-repair procedures , 7-80
power supply
check, 4-7
functional description of
, 5-5
functional group
, 5-3
if all voltages are missing
, 4-10
operation
, 5-34
voltage checks
, 4-8
power supply assembly
illustrated, 6-13, 6-17
part number
, 6-12, 6-16
removal and replacement
illustrated
, 7-17
procedure
, 7-16
troubleshooting
, 4-7
power, source
accuracy test, 3-31
linearity test, 3-32
power, source output
maximum test, 3-32
power, test port output
accuracy test, 3-31
linearity test, 3-32
maximum test
, 3-32
precautions
handling airlines, 3-24
pre-repair
procedures, 7-3
caution about
, 7-3
warnings about
, 7-3
preventive maintenance
effect on error terms, 8-3
printing copies of
documentation , -iv
probe power
connector, 5-31
measurement points
, 4-7
troubleshooting
, 4-17
processing subgroup
operation, 5-32
protection
against ESD, 1-6, 3-4, 4-3, 7-3,
8-4
protective end caps
for connectors
part numbers
, 6-80
PULSE IN connectors
operation, 5-26
pulse measurement capability,
Option H08 , 2-6
R
R1 channel
troubleshooting, 4-31
R1 receiver module
troubleshooting, 4-53
R1 trace
troubleshooting, 4-31, 4-34
R2 channel
troubleshooting, 4-31
R2 receiver module
troubleshooting, 4-53
R2 trace
troubleshooting, 4-31, 4-34
rack mount kits
part numbers, 6-82
with handles, Option 1CP
, 2-6
without handles, Option 1CM
,
2-6
raising the receiver deck
illustrated, 7-9
procedure
, 7-8
RAM, main
operation, 5-32
rear panel
connectors
1284-C, 5-33
8.33 MHz IF IN
, 5-26
AUX I/O
, 5-12
Display, 5-33
EXT 10 MHz REF IN
, 5-10
EXT 10 MHz REF OUT
, 5-10

Agilent Technologies E8362C Specifications

General

Brand	Agilent Technologies
Model	E8362C
Category	Measuring Instruments
Language	English