Airoptic GasEye - 8.4.1.8. MP1 -> Gas107

254 pages

Save Page as PDF

To Next Page

To Previous Page

WebServer application

166

GasEye Cross Duct SG and MG

Operat

ing instructions,

/202

Figure 166. GAS106 parameters window

8.4.1.8. MP1 -> Gas107

Gas parameters

Name Description

GAS107.SPAN_CALIBRATION

Multiplier of the measured concentration

GAS107.

–

factory value of multiplier

GAS107.OFFSET

Offset from measured concentration

GAS107 value

Table 37. GAS107 parameters list.

Main Page

Table of Contents5
Introduction9
General Information9
Warranty Conditions9
Delivery Information9
Calibration Information9
General Information about the Analyzer10
Introduction10
Types of Applications10
Analyzer Arrangement11
Gaseye Cross Duct Sg Mechanical Assembly11
Gaseye Cross Duct Multi Gas (Mg) Mechanical Assembly13
Functional Description15
Principle of Operation15
Technical Data15
Design, Enclosure15
Electrical Characteristics17
Dynamic Performance17
Electric Inputs and Outputs17
Customer Interface18
Climatic Conditions18
Purging18
Packaging19
Calibration and Calibration Certificate20
Installation22
Safety Information22
Mounting23
Mounting Conditions23
Preparations23
Optical Path Length Determination24
Purging Tubes25
Flange Installation (3° or 1° Wedge Window Standard Version)26
Flange Installation (1° Wedge Window Easy-To-Clean Version "Etc")28
Alignment of Gaseye Cross Duct31
Alignment Kit31
Alignment Procedure33
Sensor Mounting39
Housing Lid Opening42
Electrical Installation45
Electrical Connections45
Gaseye Cross Duct Single Gas46
Gaseye Cross Duct Multi Gas47
Gaseye Cross Duct Multi Gas Multi Point48
Central Unit - Electrical Terminals48
Power Supply52
Analog Outputs and Inputs53
Active Analog Outputs55
Passive Analog Outputs56
Active Analog Inputs57
Passive Analog Inputs58
Dout59
Din60
Rtd61
Loop (Hybrid) Cable Connection64
Receiver Unit - Loop Cable Installation Instruction65
Central Unit - Loop Cable Installation Instruction71
Customer Cable Connection73
Customer Cable Installation Instruction73
Ethernet Connection77
Ethernet Cable Installation Instruction78
Ethernet Cable Installation Instruction (Atex Version)79
Industrial Protocols Connection81
Modbus Rtu (Rs485)81
Modbus Tcp117
Profinet117
Add-On Module117
Startup Procedure121
Hmi - Front Panel Display122
Overview122
Menu123
Settings124
Diagnostic125
Measurements126
Analog Input129
Analog Output130
Signals131
Buttons131
Editing Parameters132
Editing Network Settings134
Editing Ain/Aout Scaling135
Webserver Application137
Establishing Communication with the Instrument137
User Access Level141
Measurement Tab143
Show Table144
Show Grid145
Show Plot146
Settings147
Measurement Groups148
8.3.3.1. MP1 -> Process148
8.3.3.2. MP1 -> Concentration149
8.3.3.3. MP1 -> Laser149
8.3.3.4. TEC -> Tec0150
8.3.3.5. TEC -> Tec1150
8.3.3.6. TEC -> Tec2151
8.3.3.7. TEC -> Tec3151
8.3.3.8. System -> System152
Io -> Aout (Analog Output Measurement)152
Io -> Ain (Analog Input Measurement)153
Io -> Digitalinout154
Parameters Tab156
Parameter Groups158
Mp1 -> Process (Process Environment Configuration)158
8.4.1.2. MP1 -> Gas101160
8.4.1.3. MP1 -> Gas102161
8.4.1.4. MP1 -> Gas103162
8.4.1.5. MP1 -> Gas104163
8.4.1.6. MP1 -> Gas105164
8.4.1.7. MP1 -> Gas106165
8.4.1.8. MP1 -> Gas107166
8.4.1.9. MP1 -> Gas108167
Mp1 -> Temp168
Io -> Dout (Digital Output Operating Mode Configuration)169
Io -> Aout (Analog Output Configuration)171
Io -> Ain (Analog Input Configuration)175
Io -> Rtd (Resistance Temperature Sensor Configuration)177
Io -> Amb_Press (Ambient Pressure Sensor Configuration)178
Network -> Net (Service Ethernet Port Configuration)179
Network -> Modbusrtu (Modbus Slave Transmission Configuration)180
Network -> Datarange181
System -> Rtc (Real Time Clock Configuration)183
System -> Hmi (Human-Machine Interface Configuration)183
System -> Alarm184
Settings Tab189
Factory Config Tab191
About Tab191
Purging (Non-Atex)192
Housing Purging (Optional)193
Single Gas193
Multi Gas194
Tube and Process Purging198
Atex (Zone 1 and 21 Purging System Installation)201
Basic Requirements and Safe Use201
Atex Marking203
Special Conditions for Safe Use203
Overview of Zone 1 and 21 Purging System for Gaseye Cross Duct Single Gas204
Overview of Zone 1 and 21 Purging System for Gaseye Cross Duct Multi Gas206
Technical Parameters208
Zone 1/21 Purging System209
Zone 1 and 21 Purging System Installation with Gaseye Cross Duct Single Gas209
Zone 1 and 21 Purging System Installation with Gaseye Cross Duct Multi Gas216
Differences between Single Gas and Multi Gas Systems221
Zone 1 and 21 Purging System Enclosures Mounting222
Zone 1 and 21 Purging System Adjustment Possibilities224
System Pressurization Failure Alarm225
System Electrical Connections - Intrinsic Safety Warnings226
System Conservation for Zone 1 and 21227
Contact Information227
Iecex (Zone 2 and 22 Purging System Installation)228
Basic Requirements and Safe Use228
Iecex Marking230
Special Conditions for Safe Use230
Overview of Zone 2 and 22 Purging System for Gaseye Cross Duct Single Gas231
Overview of Zone 2 and 22 Purging System of Gaseye Cross Duct Multi Gas234
Technical Parameters236
Zone 2 and 22 Purging System Installation with Gaseye Cross-Duct Single Gas237
Zone 2 and 22 Purging System Installation with Gaseye Cross-Duct Multi Gas240
Differences between Single Gas and Multi Gas Systems243
Zone 2 and 22 Purging System Enclosures Mounting243
Zone 2 and 22 Purging System Adjustment Possibilities246
System Pressurization Failure Alarm247
System Electrical Connections - Intrinsic Safety Warnings248
System Conservation for Zone 2 and 22249
Troubleshooting250
Appendix 1. Parameters List251
Appendix 2. Measurements List254

Airoptic GasEye - 8.4.1.8. MP1 -> Gas107

Table of Contents