Airoptic GasEye - Page 7

Introduction
GasEye Cross Duct
Operating i
nstructions,
0
5
/202
1
7
8.4.1.12. IO -> AOUT (ANALOG OUTPUT CONFIGURATION) .................................................................... 171
8.4.1.13. IO -> AIN (ANALOG INPUT CONFIGURATION) ........................................................................... 175
8.4.1.14. IO -> RTD (RESISTANCE TEMPERATURE SENSOR CONFIGURATION) ......................................... 177
8.4.1.15. IO -> AMB_PRESS (AMBIENT PRESSURE SENSOR CONFIGURATION) ........................................ 178
8.4.1.16. NETWORK -> NET (SERVICE ETHERNET PORT CONFIGURATION) .............................................. 179
8.4.1.17. NETWORK -> MODBUSRTU (MODBUS SLAVE TRANSMISSION CONFIGURATION) .................... 180
8.4.1.18. NETWORK -> DATARANGE ....................................................................................................... 181
8.4.1.19. SYSTEM -> RTC (REAL TIME CLOCK CONFIGURATION) .............................................................. 183
8.4.1.20. SYSTEM -> HMI (HUMAN-MACHINE INTERFACE CONFIGURATION) .......................................... 183
8.4.1.21. SYSTEM -> ALARM ................................................................................................................... 184
SETTINGS TAB ................................................................................................................................... 189
TABLE 54. SETTINGS WINDOW FUNCTIONALITIES. ..................................................................................... 189
FACTORY CONFIG TAB ....................................................................................................................... 191
ABOUT TAB ....................................................................................................................................... 191
PURGING (NON-ATEX) ...................................................................................................................... 192
HOUSING PURGING (OPTIONAL) ....................................................................................................... 193
SINGLE GAS ....................................................................................................................................... 193
MULTI GAS ........................................................................................................................................ 194
TUBE AND PROCESS PURGING .......................................................................................................... 198
ATEX (ZONE 1 AND 21 PURGING SYSTEM INSTALLATION) ................................................................. 201
BASIC REQUIREMENTS AND SAFE USE .............................................................................................. 201
ATEX MARKING ................................................................................................................................. 203
SPECIAL CONDITIONS FOR SAFE USE ................................................................................................. 203
OVERVIEW OF ZONE 1 AND 21 PURGING SYSTEM FOR GASEYE CROSS DUCT SINGLE GAS ................ 204
OVERVIEW OF ZONE 1 AND 21 PURGING SYSTEM FOR GASEYE CROSS DUCT MULTI GAS ................. 206
TECHNICAL PARAMETERS.................................................................................................................. 208
ZONE 1/21 PURGING SYSTEM ........................................................................................................... 209
ZONE 1 AND 21 PURGING SYSTEM INSTALLATION WITH GASEYE CROSS DUCT SINGLE GAS.............. 209
ZONE 1 AND 21 PURGING SYSTEM INSTALLATION WITH GASEYE CROSS DUCT MULTI GAS .............. 216
DIFFERENCES BETWEEN SINGLE GAS AND MULTI GAS SYSTEMS .............................................. 221
ZONE 1 AND 21 PURGING SYSTEM ENCLOSURES MOUNTING .................................................. 222
ZONE 1 AND 21 PURGING SYSTEM ADJUSTMENT POSSIBILITIES .............................................. 224
SYSTEM PRESSURIZATION FAILURE ALARM ............................................................................. 225
SYSTEM ELECTRICAL CONNECTIONS - INTRINSIC SAFETY WARNINGS ....................................... 226
SYSTEM CONSERVATION FOR ZONE 1 AND 21 ......................................................................... 227
CONTACT INFORMATION ......................................................................................................... 227
IECEX (ZONE 2 AND 22 PURGING SYSTEM INSTALLATION) ................................................................ 228
BASIC REQUIREMENTS AND SAFE USE .............................................................................................. 228
IECEX MARKING ................................................................................................................................ 230
SPECIAL CONDITIONS FOR SAFE USE ................................................................................................. 230
OVERVIEW OF ZONE 2 AND 22 PURGING SYSTEM FOR GASEYE CROSS DUCT SINGLE GAS ................ 231
OVERVIEW OF ZONE 2 AND 22 PURGING SYSTEM OF GASEYE CROSS DUCT MULTI GAS ................... 234
TECHNICAL PARAMETERS.................................................................................................................. 236
ZONE 2 AND 22 PURGING SYSTEM INSTALLATION WITH GASEYE CROSS-DUCT SINGLE GAS ............. 237
ZONE 2 AND 22 PURGING SYSTEM INSTALLATION WITH GASEYE CROSS-DUCT MULTI GAS .............. 240
DIFFERENCES BETWEEN SINGLE GAS AND MULTI GAS SYSTEMS ....................................................... 243
ZONE 2 AND 22 PURGING SYSTEM ENCLOSURES MOUNTING .................................................. 243
ZONE 2 AND 22 PURGING SYSTEM ADJUSTMENT POSSIBILITIES .............................................. 246
SYSTEM PRESSURIZATION FAILURE ALARM ............................................................................. 247
SYSTEM ELECTRICAL CONNECTIONS - INTRINSIC SAFETY WARNINGS ....................................... 248
SYSTEM CONSERVATION FOR ZONE 2 AND 22 ......................................................................... 249
TROUBLESHOOTING .......................................................................................................................... 250
APPENDIX 1. PARAMETERS LIST. ................................................................................................................ 251
APPENDIX 2. MEASUREMENTS LIST ............................................................................................................ 254