Akw Itherm - Temperature and Mode Configuration; Factory Default Settings; Adjusting Max Temperature; Understanding Mode Settings

29
© 2015 AKW 14-019-002-08
© 2015 AKW 13-012-085-13
27
Temperature & Mode Settings
Commissioning
Temperature Settings
The shower maximum water temperature can be set to either 41
0
C (Factory), 43
0
C or 47
0
C by setting the DIP switches
located on the control PCB inside the front cover.
Note- to comply with BEAB Care standard the shower MUST be set to 41
0
C maximum temperature
Mode Settings
MAX. TEMP. 43˚CMAX. TEMP. 41˚C MAX. TEMP. 47˚C
RNIB Mode
RESTRICTED Mode DELAYED Mode
User cannot set the temperature
below 38
0
C. User cannot set the flow
below medium
If shower is turned off by remote
control or smart device, the shower
cannot be restarted manually
within 2 minutes. The shower can be
restarted immediately by the remote
control or smart device that turned
it off.
WIRELESS PUMP WIRED PUMP
TEMP. 47˚C
TEMP. 43˚C
DELAYED
RESTRICTED
RNIB STD
WIRELESS PUMP WIRED PUMP
TEMP. 47˚C
TEMP. 43˚C
DELAYED
RESTRICTED
RNIB STD
WIRELESS PUMP WIRED PUMP
TEMP. 47˚C
TEMP. 43˚C
DELAYED
RESTRICTED
RNIB STD
WIRELESS PUMP WIRED PUMP
TEMP. 47˚C
TEMP. 43˚C
DELAYED
RESTRICTED
RNIB STD
WIRELESS PUMP WIRED PUMP
TEMP. 47˚C
TEMP. 43˚C
DELAYED
RESTRICTED
RNIB STD
WIRELESS PUMP WIRED PUMP
TEMP. 47˚C
TEMP. 43˚C
DELAYED
RESTRICTED
RNIB STD
WIRELESS PUMP WIRED PUMP
TEMP. 47˚C
TEMP. 43˚C
DELAYED
RESTRICTED
RNIB STD
WIRELESS PUMP WIRED PUMP
TEMP. 47˚C
TEMP. 43˚C
DELAYED
RESTRICTED
RNIB STD
WIRELESS PUMP WIRED PUMP
TEMP. 47˚C
TEMP. 43˚C
DELAYED
RESTRICTED
RNIB STD
When started, the shower setting
will be at a temperature of 38
0
C.
The shower will start at the flow
setting last used when the shower
was turned off.
Refer to Pump Installation instructions for further detail.
STD Mode
The shower will start at the
temperature and flow settings last
used when the shower was turned off.
Factory Settings Pump Setting
The shower is set in its factory setting when delivered.
TEMP. 41˚C
TEMP. 41˚C
TEMP. 41˚C TEMP. 41˚C TEMP. 41˚C TEMP. 41˚C
TEMP. 41˚C TEMP. 41˚C
TEMP. 41˚C
Temperature Settings
The shower maximum water temperature can be set to either 41
0
C, 43
0
C or 47
0
C (Factory) by setting the DIP switches
located on the control PCB inside the front cover.
Factory Settings Pump Setting
Mode Settings
MAX. TEMP. 43˚C MAX. TEMP. 47˚CMAX. TEMP. 41˚C
STD COLD FLUSH
TEMP. 43˚C
TEMP. 47˚C
TEMP. 41˚C
SOUND ON SOUND OFF
B/T OFF B/T ON
WIRED PUMP WIRELESS PUMP
STD COLD FLUSH
TEMP. 43˚C
TEMP. 47˚C
TEMP. 41˚C
SOUND ON SOUND OFF
B/T OFF B/T ON
WIRED PUMP WIRELESS PUMP
STD COLD FLUSH
TEMP. 43˚C
TEMP. 47˚C
TEMP. 41˚C
SOUND ON SOUND OFF
B/T OFF B/T ON
WIRED PUMP WIRELESS PUMP
STD COLD FLUSH
TEMP. 43˚C
TEMP. 47˚C
TEMP. 41˚C
SOUND ON SOUND OFF
B/T OFF B/T ON
WIRED PUMP WIRELESS PUMP
STD COLD FLUSH
TEMP. 43˚C
TEMP. 47˚C
TEMP. 41˚C
SOUND ON SOUND OFF
B/T OFF B/T ON
WIRED PUMP WIRELESS PUMP
The shower is set in its factory setting when delivered.
Refer to Pump Installation instructions for further detail.
COLD FLUSH Mode
SOUND ModeSTD Mode
The shower will start at the
temperature and flow settings last
used when the shower was turned off.
When the shower is switched on in
this mode, no heating will occur and
only cold water will flush into the
system. This will prime the heater
tank.
STD COLD FLUSH
TEMP. 43˚C
TEMP. 47˚C
TEMP. 41˚C
SOUND ON SOUND OFF
B/T OFF B/T ON
WIRED PUMP WIRELESS PUMP
STD COLD FLUSH
TEMP. 43˚C
TEMP. 47˚C
TEMP. 41˚C
SOUND ON SOUND OFF
B/T OFF B/T ON
WIRED PUMP WIRELESS PUMP
STD COLD FLUSH
TEMP. 43˚C
TEMP. 47˚C
TEMP. 41˚C
SOUND ON SOUND OFF
B/T OFF B/T ON
WIRED PUMP WIRELESS PUMP
The sound can be turned on or off
using this switch.