What to do if my AL-KO Lawn Mower is in a bad position?
If your AL-KO Lawn Mower shows a 'bad position' error, it means the appliance is outside the designated grass surface or the boundary cable has been routed in a criss-cross pattern. To fix this, place the appliance on the free, designated grass surface and correct the location of the boundary cable around curves and obstacles, eliminating any criss-crossing of the cable.
What to do if the blade motor is overheating on my AL-KO Lawn Mower?
If the mowing motor on your AL-KO Lawn Mower has overheated (more than 80 °C), switch off the appliance and let it cool down.
Why is my AL-KO Lawn Mower showing 'No loop signal'?
The 'No loop signal' error on your AL-KO Lawn Mower indicates a problem with the boundary cable. This could be due to: a faulty boundary cable, a missing loop signal, or a loop signal that is too weak. To resolve this, check the LEDs on the base station, verify the power source of the base station by disconnecting and reconnecting the power supply, and inspect the boundary cable for any damage, repairing it as necessary.
What to do if my AL-KO Robolinho 500 Lawn Mower displays 'Battery' error?
If your AL-KO Lawn Mower shows a 'Battery' error, several issues could be the cause. Here's what you can check: 1. If the rechargeable battery is flat, make sure the boundary cable location is correct. 2. If the loop of the boundary cable is too long or has too many islands, correct its location. 3. If there's no contact to the charging contacts, clean the charging contacts, ensure the appliance is properly placed in the base station, and that the charging contacts are making contact. 4. Remove any obstacles close to the base station. 5. If the appliance has gotten stuck, place it on the free, designated grass surface. 6. If the appliance does not find the base station, check the boundary cable for damage.
What to do if AL-KO Robolinho 500 shows 'Loop signal weak'?
If your AL-KO Lawn Mower displays a 'Loop signal weak' message, it means that the loop signal is too weak or the boundary cable is buried too deep. To fix this, check the LEDs on the base station, check the power source of the base station by disconnecting and reconnecting the power supply. Also, raise the boundary cable to the prescribed height, attaching it directly on the grass if necessary.
Why is the loop signal weak on my AL-KO Lawn Mower?
A weak loop signal on your AL-KO Lawn Mower can be caused by the boundary cable being buried too deep. To resolve this, check the LEDs on the base station, check the power source of the base station by disconnecting and reconnecting the power supply, and raise the boundary cable to the prescribed height, attaching it directly on the grass if necessary.
What does AL-KO Robolinho 500 Lawn Mower error 'CN099: Recov escape' mean?
The error 'Recov escape' on your AL-KO Lawn Mower means that automatic fault rectification was not possible. To solve this, manually acknowledge the malfunction message.
What to do if my AL-KO Robolinho 500 Lawn Mower has no loop signal?
If your AL-KO Lawn Mower displays a 'no loop signal' error, the boundary cable might be faulty, or the loop signal might be too weak. You can try to check the LEDs on the base station, check the power source of the base station by disconnecting and reconnecting the power supply, and inspect the boundary cable for any damage. If you find any damage, repair the defective cable.
Why does my AL-KO Robolinho 500 Lawn Mower show 'CN017: Cal: signal weak'?
If your AL-KO Lawn Mower displays 'Cal: signal weak' during calibration, it indicates a weak or missing loop signal, or a faulty boundary cable. To address this, place the appliance at the prescribed calibrating position, aligned precisely at right angles, check the power source of the base station by disconnecting and reconnecting the power supply, and check the boundary cable for damage.
What does 'CN119: R-Bumper de- flected CN120: L-Bumper de- flected' mean on my AL-KO Lawn Mower?
The error message 'R-Bumper deflected' or 'L-Bumper deflected' on your AL-KO Lawn Mower indicates that the appliance has moved onto an obstacle and cannot free itself. To solve this, simply remove the obstacle.
General| Type | Robotic lawn mower |
|---|---|
| Cutting width | 200 mm |
| Product color | Gray |
| Number of blades | 4 |
| Rotational speed | 3400 RPM |
| Maximum lawn area | 500 m² |
| Mulching function | - |
| Sound power level | 58 dB |
| Sound pressure level | 60 dB |
| Maximum cutting height | 55 mm |
| Minimum cutting height | 25 mm |
| Cutting clearance adjustment | Yes |
| International Protection (IP) code | IPX1 |
| Power source | Battery |
| Battery voltage | 20 V |
| Battery capacity | 2.5 Ah |
| Battery life (min) | 55 min |
Weight and Dimensions| Weight | 7600 g |
|---|
To Next Page
