Alpine 7294R - Page 15

_
OPERATION
Other Convenient Functions
Manual tracing operation:
When
the
A.P.I.
button
@
is
pressed
for
two
seconds
while
in
the
A.P.I.
mode
(when
the
A.P.I.
indicator
@
on
the
display
is
on),
reception
switches
to
the
station
included
among
the
AF
data
which
is
broadcasting
the
same
program
with
the
best
reception.
“AF
SEEK"
is
displayed
during
this
operation.
When
the
operation
is
completed,
“SEEK
END”
appears
on
the
display.
In
areas
where
operation
does
not
function
properly
due
to
reasons
of
the
broadcast
stations:
1.
Turn
the
auto
tracing
function
off.
Press
the
TUNE
switch
@
for
3
seconds.
And
then
press
the
Preset
No.
5
button
@.
The
display
switches
between
“PS
ONLY”
and “PS
&
API"
each
time
the
button
is
pressed.
Press
the
TUNE
switch
@
when
“PS
ONLY"
is displayed.
The
auto
follow
function
is
now
off,
but
the
station
name
is displayed.
2.
Press
the
A.P.I.
button
©
for
two
seconds
when
the
reception
of
the
station
tuned
in
iS poor.
The
set
searches
for
the
station
which
is
broadcasting
the
same
program
with
the
best
reception
among
those
included
in the
AF
data.
“AF
SEEK"
appears
on
the
display
during
the
operation.
When
the
operation
is
completed,
“SEEK
END”
appears
on
the
display.
Setting the PI in the Preset Memory
1.
Tune
in
an
RDS
station
and
set
the
display
to
the
station
name
display.
2. Press one of preset buttons 1 to 6 for two seconds.
3.
The
station
name
flashes
for
5
seconds.
Press
the
preset
button
at
which
you
want
to
store
the
Pl
while
the
display
is
flashing.
The
Pl
is
now
stored
in
the
memory.
. Set other preset buttons in the same way.
e
fa
preset
button
at
which
a
PI
is
stored
is
pressed,
the
station
name
will
be
displayed,
not
the
frequency.
e
|f
a
preset
button
at
which
a
Pl
is
stored
is
pressed
and
a
station
broadcasting
the
same
program
cannot
be
received,
“RDS
SEEK”
appears
on
the
display
after
2
seconds
and
the
set
searches
for
a station
broadcasting
the
same
program.
e
lf
astation
broadcasting
the
same
program
cannot
be
tuned
in,
reception
returns
to
the
original
frequency
and the
preset
indicator
turns
off.
RDS auto memory function
Six RDS stations can be stored in the preset memory in order according to the best
reception conditions.
Set to the RDS station reception mode.
Press the TUNE switch @ to set the AIMEMO mode, then press the UP or DN switch (@
or ©) to start the auto memory operation.
CAUTION:
1. The Pl and PS data stored in the memory are cleared when the auto memory function
is used, so set them in the memory once again.
2. The Pl and PS data are not stored in the memory when RDS stations are preset using
the auto memory function.
To use the PI memory function, press the preset button after the auto memory
operation is finished and store the Pi data in the preset memory.
15