Need help?Do you have a question about the AMF Reece S-101 and is the answer not in the manual?
Details of warranty coverage and periods.
Items not covered by the warranty.
Instructions on how to handle warranty questions.
Diagrams for threading the upper parts of the machine.
How to thread fixed type tensions.
How to thread rocking type tensions.
Diagrams for threading the lower parts of the machine.
Specific threading for cord components.
Guidance on selecting appropriate needles for the machine.
Modifying stitch entry and cutting area.
Controlling material spread in the clamps.
Changing stitch count per inch in buttonholes.
Modifying stitch density in the buttonhole eye.
Setting upper and lower thread tension.
Aligning the needle bar and race for proper function.
Ensuring loopers are correctly positioned relative to the needle.
Setting the loopers and spreaders for optimal stitch formation.
Setting the height of the needle bar.
Reducing play in the split collar yoke.
Setting the cutting lever for precise operation.
Modifying the clamp's operating mechanism.
Setting the trip lever for stitching equalization.
Fixing distortion in the buttonhole eye shape.
Setting the roll pressure on the length gauge.
Setting the rocker arm and stop motion components.
Setting the stop latch on the stitching wheel.
Setting the trigger mechanism.
Adjusting timing between handwheel and shafts.
Setting the handwheel to disengage at stop.
Setting friction on the worm shaft.
Setting friction on the main cam.
Setting the vertical position of the trimming knife.
Adjusting the trimming knife actuator.
Setting the stop position for the trimming knife.
Adjusting upper thread draw-off for rocking tension type.
Adjusting combined thread draw-off and tension release.
Diagrams for threading cord trim components.
Specific threading diagram for the cord.
Adjusting upper thread draw-off and tension.
Adjusting the thread pick-up hook mechanism.
Adjusting under thread draw-off and tension release.
Setting the thread trimmer and retainer.
Adjusting the under thread guide for smooth operation.
Theory and adjustments for proper cord functioning.
Adjusting the shear mechanism for cutting.
Setting the hold down finger for work security.
Setting buttonhole and fly bar lengths.
Adjustments for proper functioning of the fly bar.
Details on upper thread draw-off and tension.
Adjusting the upper thread draw-off.
How the under thread grabber operates.
Explanation of coloured marks on machine components.
Summary of common machine problems and remedies.
Introduction to troubleshooting procedures.
Diagnosing and fixing start-up failures.
Troubleshooting machines that stop unexpectedly.
Resolving issues causing the machine to seize.
Troubleshooting stitching failures or interruptions.
Diagnosing and correcting uneven feeding issues.
Addressing problems with hard machine turning.
Resolving stop motion mechanism issues.
Troubleshooting a sticking cutting lever.
Fixing issues with the machine's stopping position.
Resolving problems with the machine repeating cycles.
Troubleshooting machines that don't stitch after completing cycles.
Diagnosing machines that stop after short stitching.
Troubleshooting clamp operation problems.
Fixing uneven or insufficient clamp pressure.
Addressing uneven clamp spreading.
Troubleshooting improper cutting performance.
Diagnosing and fixing uneven cutting.
Troubleshooting cutting stitches on cut-after models.
Correcting distortion in the buttonhole eye.
Diagnosing and fixing skipped stitches.
Troubleshooting skipping at start or Y junction.
Troubleshooting skipping at start or Y junction.
Fixing stitches that unravel at the buttonhole end.
Troubleshooting upper thread breakage.
Resolving thread breaking or running back issues.
Diagnosing and fixing under thread breakage.
Troubleshooting needle damage.
Adjusting factors affecting buttonhole appearance.
Resolving issues with stitch pulling.
Understanding the cord trimming mechanism.
Fixing insufficient upper thread for starting.
Troubleshooting excessive upper thread length.
Resolving short under thread issues for starting.
Diagnosing under thread creeping problems.
Troubleshooting cord being too long for starting.
Fixing cord that is too short.
Troubleshooting the hold-down finger.
Diagnosing and fixing shears that don't cut.
Resolving issues with trimming not being close enough.
Troubleshooting work being drawn into the shears.
General| Brand | AMF |
|---|---|
| Model | Reece S-101 |
| Category | Sewing Machine |
| Language | English |
To Next Page
