APT 320XAC - Instrument Power Switch

161 pages

Save Page as PDF

To Next Page

To Previous Page

340XAC

360XAC

2.4 Instrument Power Switch

The power switch that is included in the instrument is not considered a

disconnecting device. It only disconnects one current carrying conductor to

power off the device. The user should configure the equipment with an external

Main Page

Table of Contents3
Introduction7
Warranty7
Glossary of Terms8
Safety Symbols11
Safety Precautions11
Service and Maintenance11
Getting Started13
Unpacking and Inspection13
Input/Output Power Considerations13
Output Current Capability15
Instrument Power Switch17
Selecting the Appropriate Wire Gauge19
Power Cable19
Supplied Input Accessories (360XAC Only)21
Environmental Conditions21
Packaging21
Specifications and Controls23
Specifications23
Instrument Controls35
Front Panel Controls35
Rear Panel Controls37
Soft Keys40
Programming Instructions42
Powering on the Instrument42
Set Screen Description43
Security44
Lock45
Mem Lock45
System Parameters Description46
Editing System Parameters49
Editing Auto Run Mode50
Editing out Mode51
Editing Single Step (PROGRAM Mode Only)51
Editing Alarm52
Editing Contrast52
Editing Power up53
Editing Loop Cycle (PROGRAM Mode Only)54
Editing V Hi-Lmt & V Lo-Lmt (MANUAL Mode Only)54
Editing F Hi-Lmt & F Lo-Lmt (MANUAL Mode Only)55
Editing Start and End Angle (MANUAL Mode Only)56
Editing Results57
Editing Transient (MANUAL Mode Only)58
Editing OC Fold59
Editing Lock59
Editing Mem Lock60
Editing Volt Sense61
Editing Sync Signal61
Editing Function (Option 08 Only)62
Using Memories and Steps (PROGRAM Mode Only)63
Selecting a Memory63
Naming a Memory65
Selecting a Step66
Test Parameters Description66
Editing Test Parameters71
Editing Start and End Angle (PROGRAM Mode Only)72
Editing the Memory Cycle (PROGRAM Mode Only)74
Editing the Memory (PROGRAM Mode Only)75
Editing the Step (PROGRAM Mode Only)75
Editing Voltage76
Editing Frequency77
Editing Transient * (PROGRAM Mode Only)77
Editing Trans-Volt* (PROGRAM Mode Only)78
Editing Trans-Site* (PROGRAM Mode Only)79
Editing Trans-Time* (PROGRAM Mode Only)80
Editing Trans-Cycle* (PROGRAM Mode Only)80
Editing Ramp up (PROGRAM Mode Only)82
Editing Timer Unit (PROGRAM Mode Only)83
Editing Delay (PROGRAM Mode Only)83
Editing Dwell (PROGRAM Mode Only)84
Editing Ramp down (PROGRAM Mode Only)85
Editing Step Cycle (PROGRAM Mode Only)85
Editing a Hi-Lmt & a Lo-Lmt (PROGRAM Mode Only)86
Editing P Hi-Lmt & P Lo-Lmt (PROGRAM Mode Only)87
Editing Ap Hi-Lmt & Ap Lo-Lmt (PROGRAM Mode Only)88
Editing CF Hi-Lmt & CF Lo-Lmt (PROGRAM Mode Only)89
Editing PF Hi-Lmt & PF Lo-Lmt (PROGRAM Mode Only)90
Editing VA Hi-Lmt & VA Lo-Lmt (PROGRAM Mode Only)91
Editing Q Hi-Lmt & Q Lo-Lmt (PROGRAM Mode Only)93
Editing Prompt94
Editing Connect95
Editing Phase Set (Option 08 - PROGRAM Mode Only)95
Reviewing Test Results96
Test Modes98
Description of Test Modes98
Initializing a Test in PROGRAM Mode98
AC Output98
DC Output100
Initializing a Test in MANUAL Mode102
AC Output102
DC Output103
Multiple Instrument Operation105
Configuring Sources for Parallel and Polyphase Operation105
Operating Mode Definitions105
Connecting the Interface Cable105
Output Wiring Diagrams106
Power up Considerations in Parallel and Polyphase Mode109
Initializing a Test in Parallel or Polyphase Mode110
Error Messages in Parallel and Polyphase Mode111
Displayed Messages112
OTP - over Temperature Protection112
OCP - over Current Protection112
OPP - over Power Protection112
OVP - Output Voltage Protection113
A-SH - Amplifier Shutdown Protection113
RCP - Reverse Current Protection113
LVP- Low Voltage Protection113
Remote PLC114
Signal Output114
Signal Input - 7 Memory Recall (Opt. 04)114
Bus Remote Interface USB/GPIB/RS-232116
USB/RS-232 Interface116
Connector117
Communication Port Configuration117
Sending and Receiving Commands117
GPIB Interface118
GPIB Connector118
GPIB Address118
Interface Functions118
USB/GPIB/RS-232 Interface Command List119
Basic Commands and Query Commands120
3Φ4W Queries123
1Φ3W Queries124
Program Commands and Companion Queries124
System Commands and Companion Queries128
IEEE 488.2 Common Commands129
Calibration Procedure134
Hardware Verification and Calibration Procedure134
Activate Non-Calibration Mode134
Adjust Control Circuit Power Voltage134
Adjust the Amplifier Inverter DC Bus Voltage135
Clear the Output High Frequency Noise135
Adjust the "0" Volts and "110" Volts DC Offset135
Adjust Wattmeter Offset136
Adjust Hardware OCP Set Point137
Exit Non-Calibration Mode137
Software Calibration Procedure137
Enter Calibration Mode139
Calibration of Voltage 150.0V139
Calibration of Voltage 300.0V140
Calibration of High and Low Current Range141
Calibration of High and Low Power Range141
Calibration of Peak Current142
Options144
Opt. 02 - Grounded Neutral144
Opt. 03 - GPIB Card144
Opt. 04 - 7 Remote Memories Select144
Opt. 06 - Ethernet Card144
Ethernet Card Setup145
Saving New Settings147
Power up147
Ethernet Card Menu149
IP Setup149
IP Address150
Gateway IP150
Subnet Mask150
Device Name151
MAC Address152
Barcode Input152
Autostart154
Ethernet Card Settings Commands and Companion Queries155
Ethernet Card Settings Command Wait Times157
Opt. 08 - Linking Card157
Service and Maintenance158
Replacement Parts List159

APT 320XAC - Instrument Power Switch

Table of Contents

Other manuals for APT 320XAC

Related product manuals