What to do if water is leaking from the Aqualisa Bathroom Fixtures shower head?
A short period of water leaking from the shower head after turning off the shower is normal. Adjust the angle of the shower head in the holder to vary the draining time and clean the shower head. If the shower flow valve is failing to close fully, possibly due to waterborne debris, remove the flow valve and check it.
Why is my Aqualisa SIERRA outlet water temperature too hot or cold?
The outlet water temperature may be too hot or cold because the inlet filter is partially blocked; check the inlet filters for any blockages and clean as necessary. It could also be due to installation conditions falling outside of the operating parameters. Also, if a stored system is used, the hot water temperature may be less than 10°c above the required blend temperature; adjust the hot water temperature or wait for the water to reheat. If you have an instantaneous water heater, it might not be igniting because the water flow rate is too low; increase the water flow rate through the system and check the inlet filters and cartridge, cleaning or replacing them as needed. Contact the boiler manufacturer.
What to do if I only get hot or cold water from my Aqualisa Plumbing Product shower valve?
If you're only getting hot or cold water, first check that the stop or service valve in the water supply pipework to the shower valve is fully open. Also, the inlet filter may be partially blocked, so clean or replace it, and flush through the pipework before refitting. Finally, the inlet water supplies might be reversed (hot to cold supply), so check the connections are the correct way round - hot on the left and cold on the right when viewed from the front. Rework the pipework as necessary.
How to stop water leaking from my Aqualisa SIERRA Plumbing Product shower head?
A small amount of water leaking from the shower head after turning off the shower is normal. To minimize this, adjust the angle of the shower head in the holder as necessary to vary draining time and clean the shower head. If the leaking persists, the shower flow valve may not be closing fully, possibly due to waterborne debris. In this case, remove the cartridge and check it.
What to do if my Aqualisa Control Unit only has hot or cold water coming from the shower valve outlet?
If you're only getting hot or cold water from your Aqualisa Control Unit, it could be due to several reasons: * A partially closed stop or service valve in the water supply pipework to the shower valve. Make sure to fully open the stop or service valve. * A partially blocked inlet filter. Clean or replace the filter, and flush the pipework before refitting. * Reversed inlet water supplies (hot connected to cold). Check that the connections are correct: hot on the left and cold on the right when viewed from the front. Rework the pipework if necessary.
Why is the outlet water temperature too hot or cold on my Aqualisa Control Unit?
If the outlet water temperature is too hot or cold, consider these possible causes: * The inlet filter may be partially blocked. Check the inlet filters for any blockages and clean as necessary. * If the hot water temperature is less than 10°c above the required blend temperature, adjust the hot water temperature or wait for water to reheat if a stored system is used. * If you have an instantaneous water heater that isn't igniting because the water flow rate is too low, increase the water flow rate through the system. Check inlet filters and cartridge, clean or replace.
Why is the maximum water temperature too hot or cold in my Aqualisa Control Unit?
If the maximum water temperature is too hot or cold, it's likely that the maximum water temperature is set incorrectly. Reset it.
Why is my Aqualisa Control Unit shower head leaking?
A small amount of water leaking from the shower head after turning off the Aqualisa Control Unit is normal for a short time. Adjust the angle of the shower head in the holder to vary the draining time and clean the shower head. Alternatively, the shower flow valve might be failing to close fully, possibly due to waterborne debris. Remove the cartridge and check it.
How to adjust a tight/loose handset holder on Aqualisa Control Unit?
If the handset holder is either too tight or too loose, it requires adjustment. Use a cross-head screwdriver in the handset holder to adjust it.
What to do if my Aqualisa Bathroom Fixtures only dispenses hot or cold water?
If your shower valve is only dispensing hot or cold water, it could be due to a partially closed stop or service valve in the water supply pipework; open the stop or service valve to resolve this. Another possibility is a partially blocked inlet filter; clean or replace it, and flush the pipework before refitting. Also, check if the inlet water supplies are reversed (hot to cold); ensure the connections are correct, with hot on the left and cold on the right when viewed from the front, and rework the pipework if necessary.
Specifies required hot/cold water temperatures and operating pressures for proper function.
Step-by-step instructions for installing the exposed shower valve.
Step-by-step instructions for installing the concealed shower valve.
How to control the shower's temperature and flow rate.
Instructions for adjusting and using the shower head and rail.
Specific instructions for removing limescale build-up from the shower head.
General| Temperature Control | Thermostatic |
|---|---|
| Frequency | 50Hz |
| Warranty | 2 Years |
| Finish | White |
| Control Type | Push Button |
| Controls | Push Button |
| Inlet Fitting | 15mm |
| Outlet Fitting | 1/2 inch |
| Voltage | 230V |
To Next Page